Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 38

Page: 38 / 114

Rotors and accessories

Be careful with damaged carbon fiber

rotors!
Never stop a running rotor manually!

Sharp carbon fiber splinters can cause

injuries.

LAC-250

The rotor consists of carbon fiber-epoxide resin com-

pound with metal components.

Compared to traditional metal rotors these composite

rotors show changed characteristics with regard to

chemical resistance. Organic solutions, strong acids

or bases can initiate premature material weakness.

Before use carefully and regularly inspect rotors

made of carbon fiber composite material for surface

wear.

The rotor may not be operated if, due to

damage, fibers escape the rotor surface!

Wear suitable protective gloves (e.g. of

leather) when handling damaged carbon

fiber rotors!

Never expose the rotor to ethylene

oxide!
Doing so will damage the composite

material.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands