Thermo Scientific 42iQD Instruction Manual Download Page 35

Page: 35 / 286

Operation

Calibration

Thermo Scientific

42iQD Instruction Manual

3-11

The Calibrate NO

Background screen is used to calibrate the instrument

zero background. Before making an adjustment, be sure the analyzer

samples zero air for at least 5 minutes.

It is important to note the averaging time when calibrating. The longer the

averaging time the more precise the calibration results. To achieve

maximum precision, allow the instrument to stabilize each time input gas is

changed and set the averaging time to 300-second averaging.

Home Screen>Calibration>Calibrate NO

Background

The Calibrate Background screen contains the following information:

●

Target NO

Concentration:

Read only. Displays what the NO

concentration value will become when the calibrate button is pressed.

●

Current NO

Concentration:

Read only. Displays what the current NO

concentration is.

●

Current NO

Background:

Read only. Displays what the current user-set

background is.

●

Calculated NO

Background:

Read only. Displays what the user-set NO

background will become when the calibrate button is pressed.

●

Calibrate:

When pressed, updates the background value, making the

concentration go to zero.

Calibrate NO

Background

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands