Thermo Scientific 42iQD Instruction Manual Download Page 255

Page: 255 / 286

Optional Equipment

Connecting External Devices

Thermo Scientific

42iQD Instruction Manual

9-9

Use the following procedure to calibrate the output channel to full scale.

This analog output calibration procedure reflects the full scale calibration

for analog output voltage for demonstration purposes. To calibrate the 20

mA current calibration, follow the same procedure, by selecting the 20 mA

current calibration option.

Note

This adjustment should only be performed by an instrument service

technician.

▲

From the Home screen, choose

Settings>Communications>Analog

I/O>Analog Output Calibration.

Depending on the output type being used, select either Analog Out

Full Scale Calibration (Voltage) or Analog Out 20.000 mA Calibration

(Current).

A confirmation screen is presented. Select Continue to proceed with

the calibration or Return to Previous Screen.

Analog Output Full Scale

Calibration

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands