manualshive.com logo in svg

Thermo Scientific 42iQD, Instruction Manual

Share
Download
Thermo Scientific 42iQD Instruction Manual Download Page 253

Optional Equipment 

Connecting External Devices 

Thermo Scientific 

42iQD Instruction Manual     

9-7

 

 

Use the following procedure to calibrate the output channel to low level. 

This analog output calibration procedure reflects the zero calibration for 

analog output voltage for demonstration purposes. To calibrate the 4 mA 

current calibration, follow the same procedure, by selecting the 4 mA 

current calibration option. 

Note  

This adjustment should only be performed by an instrument service 

technician. 

▲

  

1.

 

From the Home screen, choose 

Settings>Communications>Analog 

I/O>Analog Out Calibration.

 

 

2.

 

Depending on the output type being used, select either Analog Out 

Zero Calibration (Voltage) or Analog Out 4.000 mA Calibration 

(Current). 

 

3.

 

A confirmation screen is presented. Select Continue to proceed with 

the calibration or Return to Previous Screen. 

Analog Output Zero 

Calibration 

Summary of Contents for 42iQD































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands