Thermo Scientific 42iQD Instruction Manual Download Page 209

Page: 209 / 286

Servicing

Pump Replacement

Thermo Scientific

42iQD Instruction Manual

7-19

Use the following procedure to replace the pump.
Equipment required:

Phillips drive, #1 and #2

Turn instrument OFF, unplug power cord, and remove the cover

(

Figure 2–1

Unplug pump cable from Step POL board J7.

Disconnect tubing from pump.

Unfasten two captive hardware.

Slide pump right until keyway meets opening.

Figure 7–22.

Remove Pump, Disconnect and Unfasten

Pull pump outwards.

Note

When installing pump, make sure the pump keyway opening goes

over the keyway.

▲

Pump

Replacement

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands