Thermo Scientific 42iQD Instruction Manual Download Page 175

Page: 175 / 286

Thermo Scientific

42iQD Instruction Manual

5-1

Chapter 5

Maintenance

This chapter describes the periodic maintenance procedures that should be

performed on the instrument to ensure proper operation. Since usage and

environmental conditions vary greatly, you should inspect the components

frequently until an appropriate maintenance schedule is determined.

Read the safety precautions before beginning any procedures in this

chapter.

Equipment Damage

Some internal components can be damaged by small

amounts of static electricity. A properly grounded antistatic wrist strap

must be worn while handling any internal component. For more

information about appropriate safety precautions, see the “

Servicing

”

chapter.

▲

Use the following procedure to inspect and clean the fan filter.

Remove the fan guard from the fan and remove the filter. Refer to

“

Filter Replacement

” on page

7-6

Flush the filter with warm water and let dry (a clean, oil-free purge will

help the drying process) or blow the filter clean with compressed air.

Re-install the filter and fan guard.

Safety

Precautions

Fan Filter Inspection

and Cleaning

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands