Thermo Scientific 42iQD Instruction Manual Download Page 156

Page: 156 / 286

Calibration

Equipment Required

4-4

42iQD Instruction Manual

Thermo Scientific

Figure 4–1.

GPT System

The ozone generator must be capable of generating sufficient and stable

levels of ozone for reaction with NO to generate NO

concentrations in the

range required.

Note

Ozone generators of the electric discharge type may produce NO and

and are not recommended.

▲

A valve can be used to divert the NO flow when zero air is required at the

manifold.

The reaction chamber used for the reaction of ozone with excess NO

should have sufficient volume so that the residence time meets the

requirements specified in this chapter.

The mixing chamber is used to provide thorough mixing of the reaction

products and diluent air.

Ozone Generator

Diverter Valve

Reaction Chamber

Mixing Chamber

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands