background image

 

 

431570 G 

HIGH-EFFICIENCY DOWNFLOW / HORIZONTAL FURNACE 

INSTALLER'S INFORMATION MANUAL 

 

 

 

DOWNFLOW POSITION SHOWN 

 
 
 
 
 
 
 
 
 

R TI F I

C E

ED

SI

E

D

GN

 

 

 

 

ATTENTION, INSTALLER!

  After installing the 

furnace, show the user how to tu rn off gas and electricity to 
the furnace.  Point out control and switch locations for 
turning off gas and electricity.  Go over the User’s 
Information Manual and Section 23, “Maintaining Fu rnace 
In Good Working Order" in this manual with the user.  Make 
sure the user understands the importance of following all 
safety precautions, including what could happen if they do 
not. 

Attach the following documents to or adjacent to the 
furnace.  Tell the user where th ese documents are located. 
 
 

•  User's Information Manual 

 

•  Installer's Information Manual 

 

•  Parts List 

 

•  Warranty Information 

While these instructions have been written as accurately 
and thoroughly as possible, they can not cover every 
system variation  or contingency.  Questions of 
interpretation may arise.  For more information, solutions to 
particular problems or clarification, contact your local 
distributor or the manufacturer. 

 

ATTENTION, USER!

  Your furnace installer should 

give you the documents listed on opposite side.  You 
should immediately read the User’s Information Manual for 
important safety information to keep you and your family 
safe.  Keep these as long as you keep your f u r n a c e .  Pass 
them on to future furnace purchasers or users.  If any of the 
documents are missing or illegible, contact your installer or 
furnace manufacturer for replacement.  Throughout this 
manual, when we use the word "you" we refer to the 
qualified service technician who is responsible for 
application, installation and service of your furnace. 

? ?

Do not store or use gasoline or other flammable vapors 
and liquids in the vicinity of this or any other appliance. 

? ?

WHAT TO DO IF YOU SMELL GAS 

• 

Do not try to light any appliance. 

• 

Do not touch any electrical switch. 

• 

Do not us e any phone in your building. 

• 

Immediately call your gas supplier from a neighbor's  

 

phone.  Follow the gas supplier's instructions. 

• 

If you cannot reach gas supplier, call the fire

 

department. 

 

Summary of Contents for Thermo Pace Downflow/Horizontal Furnace

































Reviews: