Thermo King Rail Edition SLXi-DRC Maintenance Manual Download

Page: 55 / 104

TK 56433-5-MM-EN

Figure 62.

Sliding Idler Pulley Adjustment

Tensioner Pulley

Sliding Idler Pulley – Move Forward/Backward

Engine/Cross Shaft Belt

IIm

orrtta

ntt:: When replacing the compressor belt,

service tool (2042436 - Tension Tool,
139mm) must be used to set the belt
tension, this will ensure that the correct
tension is set at all times.

IIm

orrtta

ntt:: When checking the alignment of the pulleys

the service tool (2042435 - Pulley
Alignment Tool) must be used to verify the
correct positioning of theCross Shaft/
Engine Pulley / Electric Motor Belt so that
alignment is maintained.

Figure 63.

Engine/Cross Shaft Belt Arrangement

Cross Shaft/Engine
PulleyCross Shaft /
Electric Motor Pulley

Compressor Coupling

Engine to Motor/Cross
Shaft Belt

Tensioner Clutch

Back Idler Pulley

Summary of Contents for Rail Edition SLXi-DRC









































































































Search results

Summary of Contents for Rail Edition SLXi-DRC

Reviews:

Related manuals for Rail Edition SLXi-DRC

Brands by name

Popular brands

Thermo King Rail Edition SLXi-DRC, Maintenance Manual

Search results

Summary of Contents for Rail Edition SLXi-DRC

Reviews:

Related manuals for Rail Edition SLXi-DRC

Brands by name

Popular brands