thermastor Quest 335 Installation, Operation And Maintenance Instructions Download | Manualshive

Page: 1 / 24

background image

Quest 335

Installation, Operation and Maintenance Instructions

– Read and Save These Instructions –

This manual is provided to acquaint you with the

dehumidifer so that installation, operation and

maintenance can proceed successfully. Ultimate

satisfaction depends on the quality of installation and a

thorough understanding of this equipment. The dehumidifer

is built around tested engineering principles and has passed

a thorough inspection for quality of workmanship and

function.

Patent: thermastor.com/patents

Features:
•  208V and 230V 60Hz
•  Industry-leading efficiency
•  Patented, multi-coil refrigeration system
•  High-efficiency, variable-speed impeller
•  Quiet operation
•  Superior air filtration (MERV-13 standard)
•  Auto-restart after loss of power
•  Environmentally friendly R410A refrigerant
•  Low voltage external control
•  On-Board digital controls

Water Removal Rates (Pints/Day) @ 80°F 60% (RH)

Dehumidifier
335

Pints Removed

335

Gallons/Liters

42/158

4201 Lien Rd

Madison, WI 53704

www.QuestClimate.com

Toll-Free 1-877-420-1330

[email protected]

Specifcations subject to change without notice.

1

TS-1196

09/21 Rev. A

1
2
3
...
»

Summary of Contents for Quest 335

























Reviews:

No comments

Related manuals for Quest 335

Brand: Quest Engineering Pages: 6

Brand: Quest Engineering Pages: 26

Brand: Black+Decker Pages: 64

Brand: Vitek Pages: 58

Brand: INVENTOR Pages: 8

Brand: HygroMatik Pages: 56

Brand: Clarke Pages: 9

Brand: Frigidaire Pages: 4

Brand: Frigidaire Pages: 2

Brand: Frigidaire Pages: 6

Brand: Frigidaire Pages: 8

Brand: Frigidaire Pages: 11

FDF50S1 - 50 Pint Capacity Dehumidifier

Brand: Frigidaire Pages: 1

Brand: Frigidaire Pages: 9

Brand: Frigidaire Pages: 12

Brand: Frigidaire Pages: 8

Brand: Frigidaire Pages: 11

Brand: Frigidaire Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands