background image

Installation Instructions

English | 4 |

Safety

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: 

Save these instructions for the local electrical

inspector’s use. Please leave these instructions with this

unit for the owner. Show the owner the location of the

circuit breaker or fuse. Mark it for easy reference. 

OWNER:

 Please retain these instructions for future

reference.

WARNING

If the information in this manual is not followed exactly,

ire or shock may result causing property damage or

personal injury.

WARNING

If the information in this manual is not followed 

exactly, ire or shock may result causing proper

-

ty damage, personal injury or death.

 -

DO NOT store or use gasoline or other lammable

 

  vapors and liquids in the vicinity of this or any other 

 apppliance.

 - WHAT TO DO IF YOU SMELL GAS

 

DO NOT try to light any appliance.

 

DO NOT touch any electrical switch.

 

DO NOT use any phone in your building.

 

Immediately call your gas supplier from a  

  neighbor’s phone. Follow the gas supplier’s  

 instructions.

 

• If you cannot reach your gas supplier, call the ire

 

 department.

 - Installation and service must be performed by an 

  authorized servicer, service agency or the gas supplier.

WARNING

Turn off power circuit at service panel and lock out panel

before wiring this appliance. Requirement: 120 VAC, 60

Hz 15 A. Allow the appliance to cool after the power has

been turned off before servicing the appliance.

WARNING

Automatically Operated Device 

To reduce the risk of injury disconnect from power supply 

before servicing.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:

 

Use this unit only in the manner intended by the 

  manufacturer. If you have questions, contact the 

  manufacturer at the address or telephone number 

  listed on the back page.

 

Before servicing or cleaning unit, switch power off at 

  service panel and lock the service disconnecting 

  means to prevent power from being switched on 

  accidentally. When the service disconnecting means 

  cannot be locked, securely fasten a prominent 

  warning device, such as a tag, to the service panel.

WARNING

DO NOT

 repair or replace any part of the appliance

unless speciically recommended in the manuals.

Improper installation, service or maintenance can cause

injury or property damage. Refer to this manual for

guidance. All other servicing should be done by an 

authorized servicer.

WARNING

ELECTRICAL SHOCK HAZARD

 

DO NOT remove connections.

 

DO NOT use an extension cord.

 

Failure to follow these instructions can 

  result in death, ire, or electrical shock.

Summary of Contents for Masterpiece HMIB36WS























Reviews: