7
remote control, the sensitivity can be decreased
or incre-
ased
by one increment each time the button is pushed.
Incre-
ment
Sensitivity
1
very insensitive
2
insensitive
3
Standard
4
sensitive
5
very sensitive
By selecting the test presence operating mode, the set sensi-
tivity increment is not changed.
Time delay channel A light
Value range
Adjustable values "SendoPro 868-A"/"theSenda B" (app)
10 s–60 min
Adjustable values "theSenda P"
10 s, 30 s, 60 s,
2 min, 10 min,
20 min, 60 min
Control for staircase light timer switch (0.5 s "on"/10
s "off")
"SendoPro 868-A"/"theSenda B" (app)
Pulse
"theSenda P"
Button
Short presence channel A light
The time delay of channel A light can be switched off sooner
if a room is occupied only for a short time. (In fully automatic
device and semi-automatic device configuration type)
The time delay is used according to the set parameter.
Off
If someone enters an unoccupied room and it is only occupied for
up to 30 s, the light will be switched off prematurely after 2 min.
On
Time delay channel H presence
Channel H presence always switches in case of a presence,
regardless of whether configuration type is set to fully auto
-
matic device or semi-automatic. The relay contact opens if the
room is vacated only after the set time delay has expired.
Value range
Adjustable values "SendoPro 868-A"/"theSenda
B" (app)
10 s – 120 min
Adjustable values "theSenda P"
10 s, 30 s, 60 s,
2 min, 10 min,
20 min, 120 min
Switch-on delay channel H presence
The relay contact only closes when someone is present after
expiry of the set switch-on delay.
Value range
Adjustable values
0 s (no switch-on delay),
30 s, 1–10 min
Configuration type
Fully automatic device: The lighting is switched on and off
automatically. (Due to presence/absence and brightness)
"SendoPro 868-A"/"theSenda B" (app)
auto
"theSenda P"
Button A
Semi-automatic: Lights must always be switched on manually.
Switching off occurs automatically by the presence detector.
(due to absence or brightness)
"SendoPro 868-A"/"theSenda B" (app)
man
"theSenda P"
Button
Control input S
Control input S for manual switch on/off of channel A light
automatically detects push buttons or switches.
Several push buttons can be connected to control input S.
¾
Use light push button only with neutral conductor
connector.
Value range
Automatic detection of push button or switch. A signal that
is present for less than 0.7 s is detected as a push button.
Longer signals are evaluated as a switch.
auto
To adapt to user behaviour, the type of
the used signal transmitter can have
a fixed setting. Automatic detection is
deactivated.
When selecting the push button, ope-
ning contact or NO contact can also be
specified.
Switch
Push button (NO
contact)
Push button (ope-
ning contact)
Switch
Push button
S
Push button
O
Staircase light function
The lighting can be switched on and off manually.
Off
The lighting can be switched on, but not switched
off manually. It only switches off after the set time
delay.
On
Group address
This parameter is applied when using the "theSenda S" user
remote control.
A group address can be assigned to channel A light.
The group addresses can be programmed with the following
remote controls:
Group address value range
Adjustable values "SendoPro 868-A"
I, II, III, All
Adjustable values "theSenda B"
I, II, III
Adjustable values "theSenda Plug"
I–VIII, All
Adjustable values "theSenda S"
I, II
