background image

P.2

    

 

 

 
 

Parts List

 1. MAIN WING -- 1 pair

 2. SERVO MOUNTING PANEL (PL5310000) -- 1 pair

     SCREW PB2x16mm -- 4 pcs

     SCREW PWA2x8mm -- 8 pcs

     HORN PL4113101 -- 2 sets

     PUSHROD Ø1.8x115mm w/ Threads (For Aileron Servos) -- 2 pcs

     STRAPER PL4112102 -- 2 pcs

     CLEVIS PL4112103 -- 2 pcs

     FUEL TUBE Ø6x5mm -- 4 pcs    

3. WING JOINER 8x24.3x153mm (wood) -- 1 pc.

4. LINKAGE CONNECTOR 2.1mm -- 2 sets

    COVERING FILM 32x42mm -- 2 pcs

    PLYWOOD 3x32x62mm -- 1 pc.

5. FUSELAGE -- 1 pc.

    STABILIZER & ELEVATOR -- 1 set

6. TAIL LANDING GEAR PL7100001 -- 1 set

    SCREW PA3x12mm -- 2 pcs

    COLLAR 2.1mm w/ set screw -- 1 set

    TAIL WHEEL Ø25mm -- 1 pc.

7. RUDDER -- 1 pc.

8. SCREW PB2x14mm -- 4 pcs

    PUSHROD Ø1.8x695mm w/ Threads (For Elevator Servo) -- 2 pcs

    HORN PL4113101 -- 2 sets

    CLEVIS PL4112103 -- 2 pcs

    FUEL TUBE Ø6x5mm -- 2 pcs

9. SCREW PB2x16mm -- 2 pcs

    PUSHROD Ø1.8x665mm w/ Threads (For Rudder Servo) -- 1 pc.

    HORN PL4113101 -- 1 set

    CLEVIS PL4112103 -- 1 pc.

    FUEL TUBE Ø6x5mm -- 1 pc.

10. SOCKET HEAD SCREW M4x25mm -- 4 pcs

      WASHER d4xD9mm -- 4 pcs

      ENGINE MOUNT PL5111050 -- 1 set

11. FUEL TANK 320cc PL1111320 -- 1 set

     CABLE TIE 1.5x5x400mm -- 1 pc.

     DOUBLE-SIDE TAPE 40x100mm -- 1 pc.

12. LINKAGE CONNECTOR 2.1mm -- 1 set

13. THROTTLE PUSHWIRE Ø1.2x310mm -- 1 pc.

      PLASTIC TUBE d2xd3x210mm -- 1 pc.

      SOCKET HEAD SCREW M3.5x30mm -- 4 pcs

      WASHER d3.5xD8mm -- 8 pcs

      M3.5 NUT -- 8 pcs

14. COWLING -- 1 pc.

      TRANSPARENT 3D TEMPLATE -- 1 pc.

      SCREW  PWA2.6x12mm -- 4 pcs

      SILICON GROMMET d1.5xD6mm (PL1265035) -- 4 pcs

      SPINNER NUT HW2340002 -- 1 set

15. CANOPY -- 1 pc.

      DOUBLE SIDED TAPE 500mm -- 1 pc.

      SCREW PWA2.3x8mm -- 4 pcs

      SILICON GROMMET d1.5xD6mm -- 4 pcs

      PILOT PC001065B -- 1 pc.

16. FUEL TUBE Ø6x5mm -- 2 pcs

      STRAPER PL4112102 -- 2 pcs

      SPONGE 10x80x200mm -- 2 pcs

      PUSHROD Ø1.8x75mm (For Elevator Servo) -- 1 pc.

      PUSHROD CONNECTOR (PL4410010)-- 1 set

17. SCREW HM4x25mm -- 2 pcs

      WASHER d4.2xD14.5mm -- 2 pcs

      AIR SCOOP -- 1 pc.

18. DECALS A077SDEC -- 1 set

    COVERING:--

      TOUGHLON STL 350 CORSAIR BLUE

A077SPO29861312

Summary of Contents for F4U CORSAIR A077S

















Reviews: