Instruction Manual
Manual De Instrucción
Manuel D'instruction
Please read before using this unit.
Lea antes de usar esta unidad.
Veuillez lire avant d'utiliser cet appareil.
SMB-552
552-0704-ENG-SPA-FRE02
6601 Lyons Road, Bldg. A7, Coconut Creek, FL33073-9902, USA.
TEL: (954) 596-1000
FAX: (954) 596-2000
The Singing Machine Company, Inc.
!
!
!
WIRELESS MICROPHONE AND SPEAKERS
MICRÓFONO INALÁMBRICO Y ALTO-PARLANTES
MICROPHONE SANS FIL ET HAUTS-PARLEURS
www.bratz.com
TM &
MGA Entertainment, Inc.
All Right Reserved. Used under license by
The Singing Machine Co., Inc.
©
To ensure long battery life; please make sure that both the microphone and the speakers are set to the OFF
position when not in use. To be absolutely certain, we advise you to remove the batteries from both the
microphone and the speaker when they are not in use.
FUNCTION LIST
BATTERY PRECAUTIONS
The precautions below should be followed when using batteries in this device:
1.
Use only the size and type of batteries specified.
2.
Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3.
Do not mix different types of batteries together (e.g. Alkaline and Carbon Zinc) or old batteries with fresh ones.
4.
If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5.
Do not try to recharge batteries not intended to be recharged, they can overheat and rupture (Follow battery
manufacturer’s directions).
6.
Rechargeable batteries are to be removed from the product before being charged.
7.
Rechargeable batteries are only to be charged under adult supervision.
8.
Exhausted batteries are to be removed from the product.
9.
The supply terminals are not to be short-circuited.
10.
The product must only be used with the recommended transformer.
11.
The transformer is not a toy.
DC JACK
ENGLISH
VISIT OUR WEBSITE www.singingmachine.com
PRINTED IN CHINA
WIRELESS MICROPHONE
SPEAKERS
1.
LED INDICATOR
2.
ON POSITION
3.
STANDBY POSITION
4.
OFF POSITION
5.
BATTERY COMPARTMENT
6.
VOLUME CONTROL
7.
SPEAKERS
8.
FUNCTION SELECTOR (MIC+AUX/AUX/OFF)
9.
ON/OFF LED
10. BATTERY COMPARTMENT
11. AUX IN JACK
12. DC JACK
MAINTENANCE
!
A DC jack is provided for external DC power for use in a car, boat or RV. Please be sure that inside of the jack is
connected to
6V side and the outside of jack is connected to
, negative side battery.
Å
!
Transformers used with the product are to be regularly examined for damage to the cord, plug, enclosure and other
parts, and that, in the event of such damage, the products must not be used with this transformer until the damage has
been repaired.
DC Jack
DC 6V
BATTERY INSTALLATION
WIRELESS MICROPHONE
SPEAKER
1. Lift cover to reveal battery compartment.
2. Insert “9V” battery.
3. Replace cover tightly before operating.
1. Open the battery compartment cover by
unscrewing the screw.
2. Insert 4 “AA” batteries.
3. Reinstall the cover and tighten the screw.
10
6
7
8
9
1
2
3
4
5
11
12
MICROPHONE DETAILS
2. STANDBY - The switch is in the middle position. The microphone will not function. The red indicator light is on. The
microphone will use battery power.
The purpose of this setting is to maintain a connection between the microphone and the receiver when moving
around the area in which it is being used.
3. OFF - The switch is located at the bottom position.
NOTE:
The microphone will not function. The red indicator light is off. The
microphone will not use battery power.
When the microphone switch is set to OFF, noise may be generated from the speakers. Please
make sure to reduce the volume control to the low level OR switch off the speakers before turning off the
microphone.
IMPORTANT NOTE:
1. PROBLEM:
2. PROBLEM:
3. PROBLEM:
a) Insure the microphone is set to the ON position.
b) Insure the speaker function is set to MIC+AUX.
c) Adjust the volume control of the speakers accordingly.
d) Confirm the speaker battery compartment contains (4) “AA” size working batteries.
a) Confirm the speaker function switch is set to MIC+AUX.
b) Adjust the speaker volume accordingly.
c) Confirm the microphone switch is in the ON position.
d) Confirm the microphone contains (1) 9V working battery.
a) Confirm the microphone switch is set to the ON position.
b) Confirm the microphone contains (1) 9V working battery.
c) Insure the speaker function is set to MIC+AUX or AUX.
d) Increase the speaker volume accordingly.
e) Confirm the speaker battery compartment contains (4) “AA” size working batteries.
f)
Adjust the output volume of the audio source accordingly.
The microphone indicator light is ON, but there is no sound when I sing.
The speaker indicator light is ON, but there is no sound when I sing.
The audio source input I am using is switched ON, but there is no sound from the speakers.
WIRELESS MICROPHONE INFORMATION
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FOR RF EXPOSURE
SAFETY INFORMATION
IMPORTANT
NOTE:
“IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the system exceeding the RF exposure
requirements.”
Your wireless microphone contains a low power transmitter. When the EUT is powered on and it sends out radio frequency
(RF) signals. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with
safety levels for wireless devices.
To maintain compliance with the FCC's RF exposure guidelines hold the transmitter and antenna at least 1 inch (2.5
centimetres) from your face and speak in a normal voice, with the antenna pointed up and away from the face. Insure that
the antenna is at least 1 inch (2.5 centimetres) from your body when you using your wireless microphone.
Use only the supplied antenna. Unauthorized antennas, modifications, or attachments could damage the transmitter and
may violate FCC regulations.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
FCC NOTICE
This wireless microphone system complies with Part 90 of the FCC Rules. There is one frequency available for the
system. You must obtain a license for the frequency you plan to use prior to using the system.
Please view
to apply for the appropriate or phone the nearest FCC office to receive the
necessary application. Licensibility depends on how the system will be used.
http://wireless.fcc.gov/uls/
TROUBLE SHOOTING
INSTRUCTION FOR USE
1. Set the switch on the microphone to the STANDBY position.
2. To connect another audio source (such as a Mp3 player, Discman or Computer) so you can sing along with its music,
simply connect the audio output jack to the aux in jack on the back of the speaker unit.
3. Set the switch on your speaker unit to the MIC+AUX position, or to the AUX position if the microphone will not be used.
4. Adjust the volume control of your speaker unit to a comfortable level.
The wire that connects to both speakers operates as an antenna for the wireless microphone reception. It may be
necessary to extend the wire to obtain the best reception.
Your wireless microphone and speaker set is now ready for use!
NOTE:
MICROPHONE DETAILS
SETTINGS
The switch on the wireless microphone has three settings:
1. ON - The switch is in the top position. The microphone will function. The red indicator light is on. The microphone will use
battery power.
