background image

 

LCD Error / Warnings 

Required Action 

ENGINE MOTOR ERROR 

An Engine Motor is not detected when running.  
Check wiring to motors. 

ENGINE MOTOR OVERLOAD 

Motor current has exceeded recommended value.  
Check for causes of overload. (Excessive grade/
load etc.) 

ENGINE NOT CONNECTED 

Check connections between Locomotive and 
Tender. 

ENGINE MOTOR TMP SENSOR ERROR 

Motor Temperature Sensor not connected.   
Check wiring to sensor. 

FRONT PANEL FIRMWARE ERROR 

Firmware checksum not valid. Contact GATC. 

SEAT SWITCH NOT ACTIVE 

Operator must be sitting on Tender Seat. 

SMOKE TEMP SENSOR ERROR 

Smoker Temperature Sensor is not connected.  
Check wiring to Smoke Sensor. 

SOUNDS NOT LOADED 

Sound Board not initialized. Contact GATC. 

SPEED SENSOR NOT CONNECTED 

Speed Sensor is not connected.  Check wiring for 
Speed Sensor. 

TENDER MOTOR ERROR 

A Tender Motor is not detected when running.  
Check wiring to motors. 

TENDER MOTOR GETTING HOT 

Tender Motor temperature is past warning level 
temperature.  Reduce speed and/or load. 

TENDER MOTOR HOT 

Tender Motor temperature is over maximum 
allowed temperature.  Stop and let the motors cool. 

TENDER MOTOR OVERLOAD 

Tender Motor current has exceeded recommended 
value.  Check for causes of overload. (Excessive 
grade/load etc.) 

TENDER MOTOR TMP SENSOR ERROR 

Tender Motor Temperature Sensor not connected.  
Check wiring to sensor. 

To contact GATC’s Technical Support, please call 763-476-5140, or send an email to:  
[email protected] 

Summary of Contents for Pioneer Mogul (2-6-0)Steam Profile Locomotive























Reviews: