background image

 

Introduction 

General Safety Information 

Notes are used to notify of installation, 
operation, or maintenance information that is 
important but not safety related

Caution without the Safety Alert Symbol is used 
to indicate the presence of a hazard, which if 
ignored may result in property damage

Caution with the Safety Alert Symbol is used to 
indicate the presence of a hazard, which if 
ignored may result in property damage and or 
minor personal injury

.

 

Warning denotes that a potential hazard exists 
and indicates procedures that must be followed 
exactly to either eliminate or reduce the hazard, 
and to avoid serious personal injury, or prevent 
future safety problems with the product

Congratulations on the purchase of your Great American Train Company (GATC), Mogul (2-6-0) 
Steam Profile Locomotive.  This model’s authentic styling is based upon the famous Baldwin Mogul 
built by the Baldwin Locomotive Works of Philadelphia, Pennsylvania, U.S.A. during the late 1800s 
and early 1900s. Baldwin Moguls were used extensively in the narrow-gauge railroads of the Old West 
and particularly on the Denver and Rio Grande. 

All Great American Train Company Locomotives are 24 VDC battery powered for safe, efficient and 
reliable operation. Rated pulling power is awesome with its 1kW total motor power – about 1600 lbs. 
of load on a 3% grade. 

If you have any questions concerning the assembly and use, or if you feel your product is not working 
properly, contact The Great American Train Company at 763-476-5140, or visit our website at 
www.greatamericantrain.com. 
  
Read these Instructions carefully, making full use of all explanations and instructions.  The “Know 
How” of trouble free operation of your railroad depends on the degree of your understanding of the 
system and willingness to keep all components in proper operating condition.  Pay particular attention 
to all 

NOTES

CAUTIONS

, and 

WARNINGS 

to avoid the risk of personal injury or property damage.  It 

is important to understand that these 

NOTES

CAUTIONS

, and 

WARNINGS 

are not exhaustive.  The 

Great American Train Company cannot possibly know or evaluate all conceivable methods in which 
procedures may be performed, or the possible hazardous consequences of each method. 

 

Accordingly, anyone who uses a procedure that is not recommended by GATC assumes the risk of 
personal injury or property damage.  
  
When unpacking your product, inspect each crate to ensure that no damage occurred during shipping.  
If damage has occurred during shipping, contact the shipper immediately.  Remove all components 
from the shipping crates and inspect them.  If any components are missing or damaged, contact The 
Great American Train Company immediately at 763-476-5140.  Do not use or assemble the product if 
any components are damaged or missing.  Do not use substitute components not manufactured by 
The Great American Train Company. 

Summary of Contents for Pioneer Mogul (2-6-0)Steam Profile Locomotive























Reviews: