DISCONNECT THE UNIT FROM THE POWER OUTLET FOR CLEANING AND MAINTENANCE.
DO NOT IMMERSE THE H2O™ HD STEAM CLEANER IN WATER.
Cleaning procedure to remove lime scale
If your H2O™ HD Steam Cleaner begins to produce steam slower than usual or stops producing steam you may need to remove lime scale.
It is necessary to remove lime scale on a regular basis, every 25 times you use a full tank of water or once a month, especially in areas with
hard water.
To remove lime scale from the H2O™ HD Steam Cleaner, please follow these procedures:
Using the Cleaning Pin
Swirl and push the pin up and down the small hole of the steam outlet in the Main Body. Ensure that all scale debris has been removed
from the steam outlet before reassembling.
Using a cleaning solution
1. Prepare a solution of 1/3 white vinegar and 2/3 water and add to the Water Tank.
2. Ensure that steam released is aimed away from the floor or surrounding objects. Plug the unit into a properly grounded electrical outlet,
turn it ON and allow the unit to produce steam until the vinegar/water solution is used up.
3. Repeat the above procedure as many times as necessary until a normal steam flow is achieved.
4. Fill the Water Tank with fresh water and rinse out.
5. Fill the Water Tank with fresh water again, and release steam through the system until the Water Tank is empty.
6. Perform a test cleaning on a suitable isolated area after each lime scale removal to ensure that there is no debris left in the system.
Cleaning and Maintenance
!
WARNING
Use detergent to clean the accessories when they are dirty. Wash with clean water and air dry.
To clean calcium deposits building up inside the Water Tank:
Add 1-2 tablespoons of white vinegar to a full Water Tank, close the Water Tank Cap and shake the contents. DO NOT TURN THE STEAMER ON.
Let the unit sit for a few hours. Empty the Water Tank and rinse with clean water until it rinses clear.
Cleaning blocked steamer accessories:
Due to the high mineral content of water in some areas, some calcium buildup might develop inside the tip of the Jet Nozzle. To clean it, we
recommend using a spray lubricant. Spray a small burst or two of the lubricant inside the tip of the Jet Nozzle. After spraying the lubricant, fill the
steamer with water and run a continuous jet of steam through the affected accessory for several minutes to remove the deposit.
WE RECOMMEND PERFORMING THIS PROCEDURE IN A PROTECTED AND WELL-VENTILATED AREA.
Microfiber Cloth care:
Machine wash at 60 ºC (140 ºF) / Do not bleach / Do not use fabric softener.
Problem
Solution
Possible Cause
The unit does not power on
Reduced steam or no steam
Steam escapes from connections
The cleaning cloth becomes wet
The cloth gets saturated with water
after extensive use
Replace with a new cleaning cloth (optional item) or allow
cloth to cool, wring out and reattach
The unit is not plugged in or turned ON
Make sure the unit is plugged into a properly grounded
outlet and the switch is ON
Attachment is improperly connected
Turn the unit OFF, allow it to cool down, detach the
accessories and reattach them properly
Debris or obstructions at the connection
points
Remove the accessory and check and clean connection
points
Blocked Steam Nozzle
Remove Mop Head and clean the Nozzle
Water Tank is empty
Fill Water Tank
Lime scale deposit
Follow cleaning procedure to remove lime scale
Troubleshooting Guide
13
Principales caractéristiques
Vue de face
Vue de dos
1. Poignée repliable
2. Encoche de sécurité pour le cordon
3. Bouton de libération de la poignée repliable
4. Enrouleur haut
5. Bouton de libération de l’appareil à vapeur portatif
6. Appareil portatif
7. Interrupteur d’alimentation avec témoin
lumineux d’alimentation
8. Bouton de puissance de vapeur
9. Témoin de niveau de puissance de vapeur
10. Bouton de libération du réservoir d’eau
11. Témoin du réservoir d’eau
12. Réservoir d’eau
13. Filtre à eau
14. Cordon d’alimentation
15. Enrouleur bas
16. Vis de tête de balai
17. Tête de balai
18. Chiffon en microfibre
19. Patin pour moquette
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
