manualshive.com logo in svg

TGW NBS 90 PolySort, Installation, Operation & Maintenance Manual

Share
Download
TGW NBS 90 PolySort Installation, Operation & Maintenance Manual Download Page 56

NBS®90 PolySort & SP IOM 

 

 

P/N: 1193974 

Revision Date: 4/25/2019 

Page 

56

 of 

83

 

9.3: NBS90

 

SP

 

A

IR 

S

UPPLY 

R

EQUIREMENTS

 

 

NBS90 SP PNEUMATIC REQUIREMENTS 

•

 

Maximum conveyor length each way from regulator is 80'.  Locate regulator in center of 

conveyor, if possible, for maximum efficiency. 

•

 

Overhead feeder line pressure to be 100 PSI minimum 

•

 

Low pressure switch to be set at 90 PSI 

•

 

In high humidity or low temperature, use air dryer 

•

 

Use 5 micron filter  

•

 

Lockout/shutoff valve to be provided by air system installer 

•

 

Regulators pressure set to unit requirements: 

NBS90 SP 

•

 

Air take-up   50-55 PSI 

•

 

90º transfer  45-50 PSI 

NBS90 SP Formulas 

NBS 90SP transfers are actuated by a single air cylinder with a 2" bore and 1/2" stroke. 
The air consumption per transfer is calculated by: 

•

 

.0092CF (cubic feet) X CPM (cycles per min.) = SCFM (Standard Cubic Feet / Minute) 

Adding together the air requirements of all transfers connected to one regulator will give total air flow 

requirements for that NBS air system. 
 

 

Summary of Contents for NBS 90 PolySort




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands