manualshive.com logo in svg

TGW NBS 90 PolySort, Installation, Operation & Maintenance Manual

Share
Download
TGW NBS 90 PolySort Installation, Operation & Maintenance Manual Download Page 45

NBS®90 PolySort & SP IOM 

 

 

P/N: 1193974 

Revision Date: 4/25/2019 

Page 

45

 of 

83

 

8.11: NBS90

 

P

OLY

S

ORT 

S

ENSING 

S

WITCHES

 

Retroreflective photoeye Ray 10 
Adjust the retroreflective type as follows: 

•

  Determine what sizes of target the photoeye must sense. 

•

  Adjust for the worst case, usually smallest item, by loosening photoeye mounting nut and 

aligning while making sure photoeye has unobstructed view of reflector. 

•

  Move the target in and out of the field of detection to ensure that the photoeye energizes and 

de-energizes. 

Adjust the photoeye type as follows: 

•

  Loosen photoeye switch mounting bolt and adjust photoeye so that the product passes 

directly in front of the switch face, as close to the switch face as possible without making 

contact. 

•

  Check that the photoeye energizes and de-energizes as the product passes in front of the 

eye’s face. 

•

  Tighten the mounting bolt. 

 

 

 

Summary of Contents for NBS 90 PolySort




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands