TGW NBS 90 PolySort Installation, Operation & Maintenance Manual Download Page 43

Page: 43 / 83

NBS®90 PolySort & SP IOM

P/N: 1193974

Revision Date: 4/25/2019

Page

8.9: NBS90

OLY

ORT

OMPONENT

RIENTATION

Using your conveyor system layout drawing and the numbers on the I.D. tags on each component,

position and orients the conveyor sections. You must know:

•

The direction of product flow

•

The elevation height

•

The drive is positioned at the discharge end

•

The end pulley is positioned at the charge end

•

Ensure rails are aligned and snag free

IMPORTANT!

•

Do not make alterations to the equipment without consulting with

user's representative and TGW Systems. Unauthorized

modifications to the equipment may impair its function, create a

hazardous condition, affect its useful life, and/or void the warranty.

WARNING

Summary of Contents for NBS 90 PolySort




















































































Search results

Summary of Contents for NBS 90 PolySort

Reviews:

Brands by name

Popular brands

TGW NBS 90 PolySort, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for NBS 90 PolySort

Reviews:

Brands by name

Popular brands