background image

 

 

  

13

 

4. Description 

 

 

 

4.1.2.

 

Use of the sprayer

 

TEYME’s sprayer is designed for the application of chemical products for crops’ protection. The 
machine can be only used with this purpose. It is not allowed the use of this equipment for other 
purposes. If the local laws do not compel the operator to be certified, it is recommendable to be 
instructed in order to carry out a correct protection of crops and a safe handling of the chemicals to 
avoid an unnecessary risk for people and the environment while the spraying is done.   

 

4.1.3.

 

Road traffic

 

You should furnish your machine with and follow the next regulations when driving by public roads 
and other places where it is applicable the traffic code, or places where there are special laws and 
regulations about signs and lights on agricultural tools  

 

 

 

ATTENTION! The highest speed is 40 km/h for all models. This could change 
according to the current local legislation. Contact the local authorities to know the real 
highest traffic speed.  

 

4.1.4.

 

Frame 

The frame consisting in spars of highly solid and resistant UPN profile accomplishes the usual 
normal as well as extreme-condition tasks. To protect it from corrosion a primer of epoxi is applied 
and covered by highly adhesive monolayer polyurethane painting. 

 

4.1.5.

 

Tanks 

The main tank is made of polyethylene and resistant to impacts, to the UV rays and to chemical 
products. It has a round design without corners for a better cleaning and emptying. Nominal capacty 
1000, 1500, 2000, 3000 or 4000 l. It has a transparent gauge located in the rigth front part and 
another in its left or right-side part depending on the tank. The front one can be seen from the 
tractor. The filling mouth/s is/are in the uppper part depending on the tank to the left or to the right. 
One can get access to it from a footrest step. That enables the filling of the tank and insertion 
 of chemicals.   
Next to the main tank it can be found a clean water tank or rinsing out of a capacity of the 10 % of 
the main tank. And a sanitary water tank of about 15 liters of capacity.   

Summary of Contents for EOLO-GTE10





















































Reviews: