background image

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

6

EK410LT and EK410LX Battery-powered Crimping Tools

Operation

Inspect tool and dies before use. Replace any worn or 

 damaged parts. A damaged or improperly  assembled 

tool can break and strike nearby personnel. 
Failure to observe this warning could result in severe 

injury or death.

Electric shock hazard:
This tool is not insulated. When using 

this unit on or near energized electri-

cal lines, use proper personal protec-

tive equipment.
Failure to observe this warning could 

result in severe injury or death.

Wear eye protection when operating 

or servicing this tool. 
Failure to wear eye protection could 

result in serious eye injury from flying 

debris or hydraulic oil. 

Pinch points:
•  Remove battery before changing 

dies, adapters, or jaws

•  Keep hands away from the crimp-

ing tool head when crimping.

Failure to observe these warnings 

could result in severe injury or death.

•  Do not use this tool for continuous use. After 30 to 

40 cycles, allow the tool to cool for 15 minutes.

•  Do not secure this tool in a vise. This tool is 

designed for hand-held operation.

•  This tool may be used in damp or wet environ-

ments; however, air-drying is recommended before 

use if the tool becomes soaked. Damage may result 

when the tool is operated prior to thorough drying 

when electrical components are soaked.

•  Use this tool for the manufacturer’s intended 

purpose only.

Failure to observe these precautions may result in 

injury or property damage.

Charging the Battery

Read the instructions supplied with the battery charger.

LED Work Light (white)

This LED automatically turns on when the trigger is 

pulled. It remains on for 10 seconds after the trigger is 

released.

LED Indicator (red)

This tool is equipped with a special circuit board incor-

porating several important features to inform the user 

about the current status of the unit. The LED signals in 

the following cases:

What happens

Signal

What it means

Constant light for 20 seconds 

at end of cycle

Battery charge is below 

17 V at beginning of cycle*

Tool will 

not

 start, and 

constant light for 20 seconds 

when trigger is released

Battery charge is below 

16 V at beginning of cycle*

Tool will stop, and constant 

light for 20 seconds after 

trigger is released

Battery voltage drops 

below 13 V during cycle*

Tool will stop, and flashing 

light for 20 seconds when 

trigger is released

 

Motor current exceeds 

20 A during cycle
Circuit has become too hot

Flashing light for 20 seconds 

at end of cycle

 

Send tool in for service

  * Running the battery below 16 V can damage the battery.

Summary of Contents for Greenlee GATOR EK410LT













Reviews: