background image

FORM: 2391
DRAWING NO:  ICA-525-27-00005
                                                         Cessna Aircraft Company
                                                         P.O Box 7704
                                                         WICHITA, KS 67277

            ENGINEERING DRAWING AND PART LIST SIGNATURE AUTHORIZATION
               Originals Electronically Signed in the VPM System

================================================================================
REVISION:  ICA-525-27-00005  ICA ---

PKG: 0000113572                      
================================================================================
                    ORIGINATOR  (DRM) Brice Logan (APPROVE 11/22/2017 15:08:15)
               MAINTENANCE_ENG  (ALL) Stephen Taylor (APPROVE 11/22/2017 13:53:46)
               ICA_COORDINATOR  (ALL) Jason Peterson (APPROVE 11/22/2017 15:10:04)
                       PROJECT  (525 SERIES) Neil Hague (APPROVE 11/22/2017 14:03:23)
                 AIRWORTHINESS  (ALL) Chad Groene (APPROVE 11/22/2017 14:54:36)
                 ODA ICA admin  (ALL) Doug Carpenter (APPROVE 11/22/2017 14:30:41)
               ICA_COORDINATOR  (ALL) Jason Peterson (APPROVE 11/22/2017 15:11:10)
                       RELEASE  (ALL) Stephanie Haymond (APPROVE 11/22/2017 15:15:59)

Summary of Contents for Cessna 525


























































Reviews: