Texas Instruments UCD3138 Technical Reference Manual Download Page 316

Page: 316 / 532

ADC Registers

www.ti.com

316

SNIU028A – February 2016 – Revised April 2016

Submit Documentation Feedback

ADC12 Overview

// Means: Enable Digital comparator 3 interrupt when exceeding upper limit at Local level

AdcRegs.ADCCOMPLIM[5].bit.LOWER_LIMIT = 0x0FA;

// Sets the lower limit to be compared to the sixth result register

//( Note: bit does not necessarily mean one bit, but a bits field of any length

CimRegs.REQMASK.bit. REQMASK_DIGI_COMP =1;

// Means: Enable Digital comparator interrupt at CPU(CIM) level.

8.18 ADC Registers

8.18.1 ADC Control Register (ADCCTRL)

Address 00040000

Figure 8-19. ADC Control Register (ADCCTRL)

EXT_TRIG_DLY

R/W-0000 0000

EXT_TRIG_GP

IO_VAL

EXT_TRIG_GP

IO_DIR

EXT_TRIG_GP

IO_EN

EXT_TRIG_EN

EXT_TRIG_SEL

R/W-0

R-0000

SAMPLING_SEL

ADC_SEL_REF

ADC_ROUND

BYPASS_EN

R/W-000

R/W-0

R/W-111

MAX_CONV

SINGLE_

SWEEP

SW_START

ADC_INT_EN

ADC_EN

R/W-0000

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

= value after reset

Table 8-5. ADC Control Register (ADCCTRL) Register Field Descriptions

Bit

Field

Type

Reset

Description

31-24

EXT_TRIG_DLY

R/W

0000
0000

8-bit External ADC Trigger Delay configuration, LSB bit resolution equals period of
ADC Clock (High Frequency Oscillator Frequency divided by 4)

EXT_TRIG_GPIO_
VAL

R/W

Output value of ADC_EXT_TRIG pin when configured in GPIO mode

0 = ADC_EXT_TRIG pin driven low (Default)

1 = ADC_EXT_TRIG pin driven high

EXT_TRIG_GPIO_
DIR

R/W

Direction of ADC_EXT_TRIG pin when configured in GPIO mode

0 = ADC_EXT_TRIG pin configured as input (Default)

1 = ADC_EXT_TRIG pin configured as output

EXT_TRIG_GPIO_
EN

R/W

Configuration of ADC_EXT_TRIG pin

0 = ADC_EXT_TRIG pin configured in functional mode (Default)

1 = ADC_EXT_TRIG pin configured in GPIO mode

EXT_TRIG_EN

R/W

External Trigger Enable, conversions are started using the external trigger as
selectable by the EXT_TRIG_SEL bits.

0 = Disable External Trigger capability (Default)

1 = Enable External Trigger capability

Summary of Contents for UCD3138





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for UCD3138

Reviews:

Related manuals for UCD3138

Brands by name

Popular brands

Texas Instruments UCD3138, Technical Reference Manual

Search results

Summary of Contents for UCD3138

Reviews:

Related manuals for UCD3138

Brands by name

Popular brands