background image

5.3 List of Test Points

Table 5-1. Test Point Functions Found on the TPS51220A EVM-476

TEST POINT

NAME

DESCRIPTION

TP1

VIN

Measurement point for input voltage with respect to TP18

TP2

VOUT1

Measurement point for output 1 voltage with respect to TP7

TP3

VOUT2

Measurement point for output 2 voltage with respect to TP8

TP4

SW1

Output 1 switch node with respect to TP20

TP5

VREG5

5-V/100-mA output, enabled EN is high, use switch S3

TP6

SW2

Output 2 switch node with respect to TP21

TP7

GND1

Ground reference for VOUT1

TP8

GND2

Ground reference for VOUT2

TP9

VREG3

3.3-V/10-mA output should be present when input voltage is applied to EVM.

TP10

EN1

Output 1 enable signal, will be high when output is enabled via switch S1

TP11

EN2

Output 2 enable signal, will be high when output is enabled via switch S2

TP12

PG1

Output 1 power good signal, will be high when output is in regulation

TP13

PG2

Output 2 power good signal, will be high when output is in regulation

TP14

EN

5-V and 2-V reference enable signal, high when EVM is enabled with switch S3

TP15

VREF2

2-V internal reference, enabled when EN is high, use switch S3

TP16

Not used

TP17

Not used

TP18

GNDIN

Ground reference for VIN

TP19

GNDS

General ground

TP20

GND

Ground reference for SW1

TP21

GND

Ground reference for SW2

TP22

GND

General ground

TP23

GND

General ground

TP24

SYNC

Not used

www.ti.com

Test Setup

SLUU381B – SEPTEMBER 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

TPS51220A Buck Controller Evaluation Module User's Guide

7

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for TPS51220A EVM-476




























Reviews: