Texas Instruments TPL7407L7 User Manual Download Page 1

User's Guide

SLRU005 – February 2013

TPL7407L7-Channel Relay and Inductive Load Sink Driver
EVM

1

Overview

The TPL7407LEVM is a 7-Channel Relay and Inductive Load Sink Driver evaluation module that
demonstrates the TPL7407LDR integrated circuit from Texas Instruments (TI).
The TPL7407LDR is a high-performance peripheral driver designed to drive loads of many types
including: relays, stepper motors, lamps, and light emitting diodes.
The EVM is configured with seven push buttons that supply input to the TPL7407L driver and seven
relays are driven by the TPL7407Loutputs. A four terminal block can be connected to external power
supplies to provide input and relay power. All of the TPL7407Linput and output pins are accessible for
external connection.

1.1

TPL7407LEVM Features

Seven numbered push buttons control input for device testing.

Seven numbered light emitting diodes indicate relay contact closure.

Three 0.1” spaced post connector ports that allow access to all input pins, output pins, and relay
contacts.

Three open locations, per channel, on the circuit board for user supplied components.

Onboard relay loads that can be disconnected by removing surface mounted 0

Ω

resistors.

A large device clearance area that allows the use of small profile temperature forcing equipment.

Table 1. TPL7407LEVM Specification

Key Parameters

Input Supply Voltage:

0V – 5.5V

Relay Supply Voltage:

8.5V – 24V

Output Current:

0mA to 500mA

Number of Channels:

7

Onboard Load:

Seven OMRON G5NB relays

G5NB specs

Nominal coil resistance is 2,880

Ω

Nominal coil current is 8.3mA

Nominal coil voltage is 24V

Pickup voltage < 75% Nominal

Dropout voltage > 10% Nominal

Maximum coil voltage 180% Nominal

CAUTION:

Applying voltages above the limitations given in

Table 1

may cause permanent damage to

your hardware.

Gerber (layout) files are available at www.ti.com.

The EVM includes mating connectors for input, output, and contact pins.

1

SLRU005 – February 2013

TPL7407L7-Channel Relay and Inductive Load Sink Driver EVM

Submit Documentation Feedback

Copyright © 2013, Texas Instruments Incorporated

Summary of Contents for TPL7407L7




















Reviews: