manualshive.com logo in svg

Texas Instruments TMS320VC5509, Reference Manual, Page: 228 / 285

Share
Download
Texas Instruments TMS320VC5509 Reference Manual Download Page 228

Transmit Control Registers (XCR1 and XCR2)

12-21

McBSP Registers

SPRU592E

Table 12

−

5. XCR1 Bit Descriptions (Continued)

Bit

Field

Value

Description

7–5

XWDLEN1

Transmit word length 1. Each frame of transmit data can have one or two
phases, depending on the value that you load into the XPHASE bit. If a
single-phase frame is selected, XWDLEN1 in XCR1 selects the length for
every serial word transmitted in the frame. If a dual-phase frame is selected,
XWDLEN1 determines the length of the serial words in phase 1 of the frame,
and XWDLEN2 in XCR2 determines the word length in phase 2 of the frame.

000b

8 bits

001b

12 bits

010b

16 bits

011b

20 bits

100b

24 bits

101b

32 bits

other

Reserved (do not use)

4-0

Reserved

0

Reserved bits (not available for your use). They are read-only bits and
return 0s when read.

Summary of Contents for TMS320VC5509






























































































































































































































































































Reviews:

No comments