manualshive.com logo in svg

Texas Instruments TMS320VC5509, Reference Manual

The Texas Instruments TMS320VC5509 Data Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information about the product. Explore its features, specifications, and functionalities by downloading the manual from manualshive.com.

Share
Download
background image

Serial Port Control Registers (SPCR1 and SPCR2)

McBSP Registers

12-10

SPRU592E

Table 12

−

2. SPCR2 Bit Descriptions (Continued)

Bit

Description

Value

Field

7

FRST

Frame-sync logic reset bit. The sample rate generator of the McBSP
includes frame-sync logic to generate an internal frame-sync signal. You
can use FRST to take the frame-sync logic into and out of its reset state.

Note:

 This bit has a negative polarity; FRST = 0 indicates the reset state.

0

If you read a 0, the frame-sync logic is in its reset state.
If you write a 0, you reset the frame-sync logic.
In the reset state, the frame-sync logic does not generate a frame-sync
signal (FSG).

1

If you read a 1, the frame-sync logic is enabled.
If you write a 1, you enable the frame-sync logic by taking it out of its reset
state.
When the frame-sync logic is enabled (FRST = 1) and the sample rate
generator as a whole is enabled (GRST = 1), the frame-sync logic
generates the frame-sync signal FSG as programmed.

6

GRST

Sample rate generator reset bit. You can use GRST to take the McBSP
sample rate generator into and out of its reset state. 

Note:

 This bit has a

negative polarity; GRST = 0 indicates the reset state.

0

If you read a 0, the sample rate generator is in its reset state.
If you write a 0, you reset the sample rate generator.
If GRST = 0 due to a DSP reset, CLKG is driven by the McBSP internal input
clock divided by 2, and FSG is driven low (inactive). If GRST = 0 due to
program code, CLKG and FSG are both driven low (inactive).

1

If you read a 1, the sample rate generator is enabled.
If you write a 1, you enable the sample rate generator by taking it out of its
reset state.
When enabled, the sample rate generator generates the clock signal CLKG
as programmed in the sample rate generator registers. If FRST = 1, the
generator also generates the frame-sync signal FSG as programmed in the
sample rate generator registers.

Summary of Contents for TMS320VC5509






























































































































































































































































































Reviews:

No comments

Related manuals for TMS320VC5509

NEC IE-78K0-NS-P04 User Manual preview
IE-78K0-NS-P04
Brand: NEC Pages: 72
NEC ELECTRA ELITE IPK II Programming Manual preview
ELECTRA ELITE IPK II
Brand: NEC Pages: 617
NEC VERSA DOCK - SERVICE Installation Manual preview
VERSA DOCK - SERVICE
Brand: NEC Pages: 8
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Brand: Javad Pages: 35
ebm-papst R3G175-AF01-02 Operating Instructions Manual preview
R3G175-AF01-02
Brand: ebm-papst Pages: 11
SSV Embedded Systems eSOM/3517 Hardware Reference Manual preview
eSOM/3517
Brand: SSV Embedded Systems Pages: 17
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Brand: Ubiquiti Pages: 13
TP-Link VIGI NVR1004H-4P Quick Installation Manual preview
VIGI NVR1004H-4P
Brand: TP-Link Pages: 2
Anthem Audio SFD-2 MkIII Jumper Configurations preview
SFD-2 MkIII Jumper
Brand: Anthem Audio Pages: 2
Altimium CVHH2 User Manual preview
CVHH2
Brand: Altimium Pages: 12
Z3 Technology DM8168-MOD-35 Manual preview
DM8168-MOD-35
Brand: Z3 Technology Pages: 22
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Brand: Magewell Pages: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Brand: Z3 Technology Pages: 18
Keithley 7075 Instruction Manual preview
7075
Brand: Keithley Pages: 108
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2
LST ZEB2-1 Specifications preview
ZEB2-1
Brand: LST Pages: 1

Brands by name

Popular brands

Load more brands