manualshive.com logo in svg

Texas Instruments TMS320VC5509, Reference Manual, Page: 215 / 285

Share
Download
Texas Instruments TMS320VC5509 Reference Manual Download Page 215

Serial Port Control Registers (SPCR1 and SPCR2)

McBSP Registers

12-8

SPRU592E

Table 12

−

1. SPCR1 Bit Descriptions (Continued)

Bit

Description

Value

Field

1

RRDY

Receiver ready bit. RRDY is set when data is ready to be read from
DRR[1,2]. Specifically, RRDY is set in response to a copy from RBR1 to
DRR1.
If the receive interrupt mode is RINTM = 00b, the McBSP sends a receive
interrupt request to the CPU when RRDY changes from 0 to 1.
Also, when RRDY changes from 0 to 1, the McBSP sends a receive
synchronization event (REVT) signal to the DMA controller.

0

Receiver not ready
When the content of DRR1 is read, RRDY is automatically cleared.

1

Receiver ready: New data can be read from DRR[1,2].
Important: If both DRRs are needed (word length larger than 16 bits), the
CPU or the DMA controller must read from DRR2 first and then from DRR1.
As soon as DRR1 is read, the next RBR-to-DRR copy is initiated. If DRR2
is not read first, the data in DRR2 is lost.

0

RRST

Receiver reset bit. You can use RRST to take the McBSP receiver into and
out of its reset state. 

Note:

 This bit has a negative polarity; RRST = 0

indicates the reset state.

0

If you read a 0, the receiver is in its reset state.
If you write a 0, you reset the receiver.

1

If you read a 1, the receiver is enabled.
If you write a 1, you enable the receiver by taking it out of its reset state.

Summary of Contents for TMS320VC5509






























































































































































































































































































Reviews:

No comments