manualshive.com logo in svg

Texas Instruments TMS320VC5509, Reference Manual

The Texas Instruments TMS320VC5509 Data Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information about the product. Explore its features, specifications, and functionalities by downloading the manual from manualshive.com.

Share
Download
background image

Setting the Receive Clock Mode

Receiver Configuration

7-32

SPRU592E

Table 7

−

23. Register Bits Used to Set the Receive Clock Mode (Continued)

Register

Function

Name

Bit

SPCR1

12-11 CLKSTP

Clock Stop Mode

CLKSTP = 0Xb

Clock stop mode disabled; normal clocking for non-SPI
mode.

CLKSTP = 10b

Clock stop mode enabled, without clock delay. The
internal receive clock signal (CLKR) and the internal
receive frame-synchronization signal (FSR) are internally
connected to their transmit counterparts, CLKX and FSX.

CLKSTP = 11b

Clock stop mode enabled, with clock delay. The internal
receive clock signal (CLKR) and the internal receive
frame-synchronization signal (FSR) are internally
connected to their transmit counterparts, CLKX and FSX.

7.19.1 Selecting a Source for the Receive Clock and a Data Direction for the

CLKR Pin

Table 7

−

24 shows how you can select various sources to provide the receive

clock signal and the effect on the CLKR pin. The polarity of the signal on the
CLKR pin is determined by the CLKRP bit.

Note that in the digital loop back mode (DLB = 1), the transmit clock signal is
also used as the receive clock signal.

Also, in the clock stop mode, the internal receive clock signal (CLKR) and the
internal receive frame-synchronization signal (FSR) are internally connected
to their transmit counterparts, CLKX and FSX.

Summary of Contents for TMS320VC5509






























































































































































































































































































Reviews:

No comments

Related manuals for TMS320VC5509

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
IEI Technology KINO-KBN-i2 Quick Installation Manual preview
KINO-KBN-i2
Brand: IEI Technology Pages: 21
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Freescale Semiconductor MCF54455 Reference Manual preview
MCF54455
Brand: Freescale Semiconductor Pages: 921
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Brand: Analog Devices Pages: 8
Belkin F5D9001 Series Manual preview
F5D9001 Series
Brand: Belkin Pages: 72
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Brand: ADC Pages: 7
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Brand: ekwb Pages: 2
IBASE Technology IB952 Series User Manual preview
IB952 Series
Brand: IBASE Technology Pages: 71
Net to Net Technologies UIM-1000T Installation Instructions preview
UIM-1000T
Brand: Net to Net Technologies Pages: 4
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Brand: Acromag Pages: 23
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21

Brands by name

Popular brands

Load more brands