manualshive.com logo in svg

Texas Instruments TMS320VC5501, Instruction Cache, Page: 23 / 30

Share
Download
Texas Instruments TMS320VC5501 Instruction Cache Download Page 23

I-Cache Registers

23

Instruction Cache

SPRU630C

Table 4.

I-Cache Global Control Register (ICGC) Bits 

Bit

Field

Description

15

−

13

Reserved

Always write 110b to these reserved bits.

12

FLUSHLINE

Flush the cache line specified by the flush line address registers 
(ICFARH and ICFARL). The line flush starts when a 1 is written to the
FLUSHLINE bit. The I-cache clears this bit to 0 when the line flush is
completed. Line flushes can be performed only when the I-cache is
enabled.

11

−

0

Reserved

Always write E3Ch to these reserved bits.

A line flush invalidates the line valid (LV) bit for a specific line in the cache. The
address associated with the line to be flushed is contained in the flush line
address registers (ICFARL and ICFARH). ICFARL contains the least
significant 16 bits of the address associated with the line to be flushed.
ICFARH contains the most significant 8 bits of the address associated with the
line to be flushed. The address specified in these registers is a byte address.
See section 6.2 on page 24 for information about ICFARH and ICFARL.

To flush a cache line associated with a specific program memory address,
perform the following steps:

Step 1:

Write the least-significant 16 bits of the address to ICFARL.

Step 2:

Write the most-significant 8 bits of the address to ICFARH. The
upper 8 bit of ICFARH should be written as zeroes.

Step 3:

Write the value DE3Ch to ICGC to initiate a line flush.

Step 4:

When the line flush is complete, the FLUSHLINE bit is automatically
cleared.

Summary of Contents for TMS320VC5501































Reviews:

No comments