manualshive.com logo in svg

Texas Instruments TMS320C6201, Reference Manual

The Texas Instruments TMS320C6201 is a highly efficient digital signal processor. Ensure smooth functioning of your device by staying updated with the latest Errata Corrections. Download the comprehensive user manual for free from manualshive.com, providing step-by-step instructions, troubleshooting tips, and optimization techniques essential for harnessing the full potential of this powerful product.

Share
Download
background image

Emulation Design Considerations

15-19

Designing for JTAG Emulation

Figure 15–9. EMU0/1 Configuration

Open

Collector

Drivers

EMU0/1-IN

Backplane

Target Board m

TCK

XCNT_ENABLE

Pullup Resistor

To Emulator EMU0

PAL

Pullup
Resistor

Open

Collector

Drivers

Target Board 1

EMU0/1

Pullup Resistor

EMU0/1-OUT

. . .

Device

Device

EMU0/1

. . .

. . .

. . .

. . .

. . .

1

n

Device

Device

1

n

Notes:

1) The low time on EMUx-IN should be at least one TCK cycle and less than 10 

m

s. Software will set the EMUx-OUT

pin to a high state.

2) To enable the open-collector driver and pullup resistor on EMU1 to provide rising/falling edges of less than  25 ns,

the modification shown in this figure is suggested.   Rising edges slower than 25 ns can cause the emulator to detect
false edges during the RUNB command or when the external counter selected from the debugger analysis menu
is used.

These seven important points apply to the circuitry shown in Figure 15–9 and
Figure 15–10 , and the timing shown in  Figure 15–11:

-

Open-collector drivers isolate each board. The EMU0/1 pins are tied to-
gether on each board.

-

At the board edge, the EMU0/1 signals are split to provide IN/OUT. This
is required to prevent the open-collector drivers from acting as a latch that
can be set only once.

-

The EMU0/1 signals are bused down the backplane. Pullup resistors are
installed as required.

-

The bused EMU0/1 signals go into a PAL

R

 device, whose function is to

generate a low pulse on the EMU0/1-IN signal when a low level is detected

Summary of Contents for TMS320C6201






























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320C6201

F5 WANJet 500 Quick Start Card preview
WANJet 500
Brand: F5 Pages: 2
F5 ARX-500 Hardware Reference Manual preview
ARX-500
Brand: F5 Pages: 90
F5 ARX-4000 Parts Replacement Manual preview
ARX-4000
Brand: F5 Pages: 47
Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Brand: Blackrock Microsystems Pages: 27
ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Brand: ekwb Pages: 7
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Brand: ANEP Pages: 48
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Brand: BIIZZY Pages: 2
ZyXEL Communications PK5000Z How To Configure preview
PK5000Z
Brand: ZyXEL Communications Pages: 3
EZCast Pro Dongle II User Manual preview
Pro Dongle II
Brand: EZCast Pages: 24
IEI Technology PE-6S-R40 User Manual preview
PE-6S-R40
Brand: IEI Technology Pages: 4
Laser UDC CARD User Manual preview
UDC CARD
Brand: Laser Pages: 4
ICP ICP9014RO Installation And User Manual preview
ICP9014RO
Brand: ICP Pages: 142
Freescale Semiconductor KW2xD Series Reference Manual preview
KW2xD Series
Brand: Freescale Semiconductor Pages: 42
Paradyne SMD2000-24E Installation Instructions Manual preview
SMD2000-24E
Brand: Paradyne Pages: 28
IBASE Technology 11th Gen Intel Core U-Series User Manual preview
11th Gen Intel Core U-Series
Brand: IBASE Technology Pages: 70
National Instruments GPIB-120A User Manual preview
GPIB-120A
Brand: National Instruments Pages: 36

Brands by name

Popular brands

Load more brands