manualshive.com logo in svg

Texas Instruments TMS320C6201, Reference Manual

The Texas Instruments TMS320C6201 is a highly efficient digital signal processor. Ensure smooth functioning of your device by staying updated with the latest Errata Corrections. Download the comprehensive user manual for free from manualshive.com, providing step-by-step instructions, troubleshooting tips, and optimization techniques essential for harnessing the full potential of this powerful product.

Share
Download
background image

SDRAM Interface

 

9-20

9.4

SDRAM Interface

The TMS320C6201/C6202/C6701 EMIF supports 2-bank, 16M-bit SDRAM
and 4 bank, 64M-bit SDRAM, providing an interface to high-speed and high-
density memory. The EMIF supports the SDRAM commands shown in
Table 9–8. The 16M-bit and 64M-bit SDRAM interfaces are shown in
Figure 9–14 and Figure 9–16, respectively. Table 9–9 lists all of the possible
SDRAM configurations available via the TMS320C6201/C6202/C6701 EMIF.

The TMS320C6211/C6711 EMIF allows programming of the addressing char-
acteristics of the SDRAM, including the number of column address bits (page
size), the row address bits (pages per bank), and banks (maximum number of
pages which can be opened). Using this information, the ’C6211/C6711 is able
to open up to four pages of SDRAM simultaneously. The pages can all be in a
single CE space, or distributed across multiple CE spaces. Table 9–10 summa-
rizes the pin connection and related signals specific to SDRAM operation.

Table 9–8 does not apply to the ’C6211/C6711 because page characteristics
are programmable. The ’C6211/C6711 can interface to any SDRAM that has
8 to 10 column address pins, 11 to 13 row address pins, and two or four banks.

Table 9–8. TMS320C6201/C6202/C6701 EMIF SDRAM Commands

Command

Function

DCAB

Deactivate all banks

DEAC

†

Deactivate a single bank

†

ACTV

Activates the selected bank and select the row

READ

Inputs the starting column address and begins the read operation

WRT

Inputs the starting column address and begins the write operation

MRS

Mode register set, configures SDRAM mode register

REFR

Autorefresh cycle with internal address

† TMS320C6211/C6711 only

Summary of Contents for TMS320C6201






























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320C6201

D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Brand: Teagle Pages: 40
Dahua NVR2104-S2 Quick Start Manual preview
NVR2104-S2
Brand: Dahua Pages: 6
Furuno 001-558-430 Replacement Instructions Manual preview
001-558-430
Brand: Furuno Pages: 24
Belkin F5D9001 Series Manual preview
F5D9001 Series
Brand: Belkin Pages: 72
peplink balance ONE Manual preview
balance ONE
Brand: peplink Pages: 2
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
Z-Wave RAZBERRY 7 PRO Quick Start Manual preview
RAZBERRY 7 PRO
Brand: Z-Wave Pages: 6
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
Renesas R0E530650CFJ30 User Manual preview
R0E530650CFJ30
Brand: Renesas Pages: 4
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
SeaLevel PC-ACB.MP User Manual preview
PC-ACB.MP
Brand: SeaLevel Pages: 21
ETAS XETK-S22.0 User Manual preview
XETK-S22.0
Brand: ETAS Pages: 84
Keil RTX51 Manual preview
RTX51
Brand: Keil Pages: 68
Cowlacious Designs ISD CAP 275 Manual preview
ISD CAP 275
Brand: Cowlacious Designs Pages: 8
Ross ULTRIX-FM-NS-1RU Install Manual preview
ULTRIX-FM-NS-1RU
Brand: Ross Pages: 5
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Brand: Microchip Technology Pages: 41
Xtreme SNMP-R90 User & Installation Manual preview
SNMP-R90
Brand: Xtreme Pages: 83

Brands by name

Popular brands

Load more brands