Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 873 | Manualshive

Page: 873 / 1141

background image

14.6.2.13 I2C Prescaler (I2CPSC) Register (Offset = Ch) [reset = 0h]

The I2C prescaler register (I2CPSC) is a 16-bit register used for dividing down the I2C input clock to obtain the
desired module clock for the operation of the I2C module. See the device-specific data manual for the supported
range of values for the module clock frequency. IPSC must be initialized while the I2C module is in reset (IRS =
0 in I2CMDR). The prescaled frequency takes effect only when IRS is changed to 1. Changing the IPSC value
while IRS = 1 has no effect.

Figure 14-31. I2C Prescaler (I2CPSC) Register

15

14

13

12

11

10

9

8

RESERVED

R-0h

7

6

5

4

3

2

1

0

IPSC

R/W-0h

Table 14-22. I2C Prescaler (I2CPSC) Register Field Descriptions

Bit

Field

Type

Reset

Description

15-8

RESERVED

R

0h

Reserved

7-0

IPSC

R/W

0h

I2C prescaler divide-down value.
IPSC determines how much the CPU clock is divided to create the
module clock of the I2C module:
module clock frequency = I2C input clock frequency/(IPSC + 1)
Note: IPSC must be initialized while the I2C module is in reset (IRS =
0 in I2CMDR).
Reset type: SYSRSn

Inter-Integrated Circuit Module (I2C)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

873

Copyright © 2022 Texas Instruments Incorporated

«
...
871
872
873
874
875
...
»

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320 2806 Series

Brand: Häfele Pages: 24

Brand: HANYOUNG NUX Pages: 56

Brand: York Pages: 24

Brand: Davey Pages: 12

Brand: Frico Pages: 12

Brand: AC Tech Pages: 2

Brand: V-TAC Pages: 2

ZigBee Pro VT8000 Series

Brand: Viconics Pages: 3

Brand: PI Pages: 111

Brand: XINGDASHINE Pages: 3

Brand: X10 Pages: 3

AGCO RoGator Hawkeye C Series

Brand: Raven Pages: 64

Brand: Arbor Technology Pages: 79

Brand: Hanna Instruments Pages: 16

Brand: Mesto Pages: 12

Brand: WAC Pages: 5

Brand: Advantech Pages: 46

Brand: Minebea Intec Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands