manualshive.com logo in svg

Texas Instruments TMP1075EVM, User Manual, Page: 21 / 33

Share
Download
Texas Instruments TMP1075EVM User Manual Download Page 21

www.ti.com

TMP1075EVM Setup and Operation

21

SNOU157A – March 2018 – Revised April 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

TMP1075EVM User's Guide

7.6

EVM Set-Up Tab

It is necessary to configure the TMP1075 slave address as 0x48 for communication with the EVM-GUI.
This is the default slave address.

Figure 24. TMP1075 Set-Up

Firmware

is allowed to check the firmware revision on the MSP430F5528 microcontroller by clicking the

Read

button or

Update The Firmware Revision

.

I2C Configuration

is to change the bus frequency and slave address.

Software Reset

performs software reset on the TMP1075 device by issuing a general call. After software

reset, the values displayed in the EVM software may be out of sync with the device register contents. To
sync register contents after software reset, click Read All in the Registers tab page.

Demo Mode

allows to operate the GUI without a hardware connected. In this mode, the handle is closed.

Clicking on any buttons or drop-down menu will be automatically closed the software GUI.

User Interface

polling rate refers to the time interval at which the GUI software queries the TMP1075

device. It can be configured here, but it will be changed automatically when changes are made to
resolution bit.

Summary of Contents for TMP1075EVM


































Reviews:

No comments