Texas Instruments TMP1075EVM User Manual Download Page 13 | Manualshive

Page: 13 / 33

Texas Instruments TMP1075EVM User Manual Download Page 13

Upgrading the Firmware

13

SNOU157A – March 2018 – Revised April 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

TMP1075EVM User's Guide

Figure 13. Firmware Update Confirmation

Figure 14. TMP1075EVM Connection Diagram

To update the firmware of the TMP1075EVM, please following the procedure below.

1. Start the

MSP430 USB Firmware Upgrade Example

program as shown in

, and click on

Next

to proceed the update and accept the license agreement. Note that in

, it shows

No device

connected

at this time.

2. Before starting the upgrade, the BSL mode must be invoked by disconnecting the TMP1075EVM from

the USB cable.

3. Press and hold the SW1 switch button down while connecting the USB cable.

4. Once the BSL mode is now invoked, the

MSP430 USB Firmware Upgrade Example

shows

Found 1

device

in

.

5. Select the

Select Firmware

radio button and click on

Browse

button to navigate the firmware file in this

folder

C:\Program Files (x86)\Texas Instruments\TMP1075EVM\Firmware

. The firmware file name is

USB2ANY_F5528.txt

version v2.7.16.

6. The firmware image is programmed, and the TMP1075EVM restarts automatically. The new firmware

is now ready to use as shown in

«
...
11
12
13
14
15
...
»

Summary of Contents for TMP1075EVM


































Reviews:

No comments