background image

User’s Guide

PGA2505EVMV2 Evaluation Module

ABSTRACT

This user’s guide describes the characteristics, operation, and use of the PGA2505EVMV2, a refreshed 
evaluation module (EVM) compatible with the 

PGA2505

 on a modern operating system. This document includes 

the schematic, printed circuit board (PCB) layout, and bill of materials (BOM). Throughout this document, the 
terms evaluation board, evaluation module, and EVM are synonymous with the universal PGA2505EVMV2.

Table of Contents

1 Product Overview

...................................................................................................................................................................

3

2 Features

...................................................................................................................................................................................

6

3 Getting Started

........................................................................................................................................................................

7

3.1 Electrostatic Discharge Caution.........................................................................................................................................

7

3.2 Unpacking the EVM...........................................................................................................................................................

7

3.3 Absolute Maximum Operating Conditions..........................................................................................................................

8

4 Setup Guide

.............................................................................................................................................................................

9

4.1 Analog and Digital Power Supplies....................................................................................................................................

9

www.ti.com

Table of Contents

SBOU259 – OCTOBER 2021

Submit Document Feedback

PGA2505EVMV2 Evaluation Module

1

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for PGA2505EVMV2
























Reviews: