Texas Instruments OMAP5910 Technical Reference Manual Download Page 782

Page: 782 / 1209

UART/IrDA Control and Status Registers

12-67

UART Devices

The interrupt enable register (IER) in SIR mode can be programmed to enable/
disable any of the following interrupts:

Received error

LSR

TX underrun

Status FIFO

RX overrun

Last byte in RX FIFO

THR

RHR

Each of these interrupts can be enabled/disabled individually. There is also a
sleep mode enable bit.

Table 12–56. SIR Mode Interrupt Enable Register (SIR_IER)

Bit

Name

Value

Function

R/W

Reset

Value

EOF_IT

Disables the received EOF interrupt

R/W

Enables the received EOF interrupt

LINE_STS_IT

Disables the receiver line status interrupt

R/W

Enables the receiver line status interrupt

TX_UNDERRUN_IT

Disables the TX underrun interrupt

R/W

Enables the TX underrun interrupt

STS_FIFO_TRIG_IT

Disables status FIFO trigger level interrupt

R/W

Enables status FIFO trigger level interrupt

RX_OVERRUN_IT

Disables the RX overrun interrupt

R/W

Enables the RX overrun interrupt

LAST_RX_BYTE_IT

Disables the last byte of frame in RX FIFO
interrupt

R/W

Enables the last byte of frame in RX FIFO
interrupt

THR_IT

Disables the THR interrupt

R/W

Enables the THR interrupt

RHR_IT

Disables the RHR interrupt

R/W

Enables the RHR interrupt

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP5910

Reviews:

Related manuals for OMAP5910

Brands by name

Popular brands

Texas Instruments OMAP5910, Technical Reference Manual

Search results

Summary of Contents for OMAP5910

Reviews:

Related manuals for OMAP5910

Brands by name

Popular brands