manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

Interrupt Handlers

 

8-22

The mask interrupt register (MIR) operates after interrupt input register (ITR);
this means that occurrences of incoming interrupts are always stored in
interrupt input register (ITR).

Table 8–25. IRQ Binary-Coded Source Register (SIR_IRQ)

Bit

Name

Type

Reset

Value

3–0

IRQ_NUM

R

0

This register saves software processing time by recognizing the interrupt
number as being either an IRQ or FIQ request. Reading this register clears the
corresponding bit in the interrupt input register (ITR) if the interrupt is set as
edge-sensitive. This register will not normally be used since all level 2 DSP
interrupts must be configured as FIQ to generate DSP interrupts because IRQ
is not connected.

Table 8–26. FIQ Binary-Coded Source Register (SIR_FIQ)

Bit

Name

Type

Reset

Value

3–0

FIQ_NUM

R

0

In order to save software processing time, this register indicates the interrupt
number that has an IRQ or FIQ request. Reading this register clears the corre-
sponding bit in the interrupt input register (ITR) if the interrupt is set as
edge-sensitive.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
Sangoma A200 Analog Installation Manual preview
A200 Analog
Brand: Sangoma Pages: 6
PMD DK55110 Manual preview
DK55110
Brand: PMD Pages: 74
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Brand: Cabletron Systems Pages: 42
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Brand: Hauppauge Pages: 62
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Brand: BIIZZY Pages: 2
XtendLan XL-IPM401 User Manual preview
XL-IPM401
Brand: XtendLan Pages: 21
Ariesys AMK Series User'S Reference Manual preview
AMK Series
Brand: Ariesys Pages: 10
VideoWave Adam Device User Manual preview
Adam Device
Brand: VideoWave Pages: 12
Crown PIP-AF Owner'S Manual preview
PIP-AF
Brand: Crown Pages: 7
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Brand: Areca Pages: 2
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Brand: Paradyne Pages: 108
SonicWALL Internet Security Appliances Administrator'S Manual preview
Internet Security Appliances
Brand: SonicWALL Pages: 293
Hameg HM6050-2K Manual preview
HM6050-2K
Brand: Hameg Pages: 46
Intel P4000CR Installation Instructions Manual preview
P4000CR
Brand: Intel Pages: 11
ZALMAN CNPS7000B Series User Manual preview
CNPS7000B Series
Brand: ZALMAN Pages: 9
Magtek IntelliStripe 65 Technical Reference Manual preview
IntelliStripe 65
Brand: Magtek Pages: 44
Crestron 8 Channel Dimmer Module CLX-1DIM8 Specification Sheet preview
8 Channel Dimmer Module CLX-1DIM8
Brand: Crestron Pages: 1

Brands by name

Popular brands

Load more brands