manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

Inter-Integrated Circuit Controller

 

7-88

-

Poll receive data: Poll the receive data ready interrupt flag bit (RRDY) in
the I

2

C status register (I2C_STAT), use the RRDY interrupt, or use the

DMA to read the receive data in the data receive register (I2C_DATA).

-

Poll transmit data: Poll the transmit data ready interrupt flag bit (XRDY) in
the I

2

C status register (I2C_STAT), use the XRDY interrupt, or use the

DMA to write data into the data transmit register (I2C_DATA).

Interrupt subroutines:

1) Test for arbitration lost and resolve accordingly.
2) Test for no-acknowledge and resolve accordingly.
3) Test for register access ready and resolve accordingly.
4) Test for receive data and resolve accordingly.
5) Test for transmit data and resolve accordingly.

7.8.4

Flowcharts

Figure 7–31 through Figure 7–42 show the master/slave I

2

C flowcharts.

Figure 7–31. Setup Procedure

Start

Write I

2

C_OA.

Write I

2

C_IE.

Write I

2

C_SCLL.

Write I

2

C_SCLH.

Use

repeat mode

(RM=1)

?

Write I

2

C_CNT.

No

Yes

Write I

2

C_SA.

End

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

3Com 3C16080 Important Information preview
3C16080
Brand: 3Com Pages: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Brand: 3Com Pages: 74
3Com 3C421600A Installation Manual preview
3C421600A
Brand: 3Com Pages: 6
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Brand: Tandberg Data Pages: 2
Renesas F-ZTAT H8/3048 Series User Manual preview
F-ZTAT H8/3048 Series
Brand: Renesas Pages: 34
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
Reeven NAIA Installation Manual preview
NAIA
Brand: Reeven Pages: 2
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
Cateye Urban Wireless CC-VT240W Instruction Manual preview
Urban Wireless CC-VT240W
Brand: Cateye Pages: 15
XMOS XC-2 Quick Start Manual preview
XC-2
Brand: XMOS Pages: 6
Matrox Millennium P650 User Manual preview
Millennium P650
Brand: Matrox Pages: 54
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
COUGAR Vortex SPB 120 User Manual preview
Vortex SPB 120
Brand: COUGAR Pages: 2
Proxim 68568r1 Installation And Management Manual preview
68568r1
Brand: Proxim Pages: 65
Quantum MC300 Prism User Manual preview
MC300 Prism
Brand: Quantum Pages: 140

Brands by name

Popular brands

Load more brands