manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

DSP Memory

3-11

DSP Subsystem

3.3.2

Instruction Cache

The DSP instruction cache (I-cache) module is a special-purpose, tightly
coupled, RAM-based program memory. The module is designed to
significantly improve the CPU performance by buffering the instructions most
recently fetched from external memory. The entire external program memory
space is cacheable.

The I-cache consists of the following:

1) One 2-way cache. The cache uses two-way set associative mapping and

holds up to 16K bytes: 512 sets, two lines per set, four 32-bit words per
line.

2) Two RAM sets (1 and 2). These two banks of RAM can be used to store

blocks of code. Each RAM set holds up to 4K bytes: 256 lines, four 32-bit
words per line. Before enabling the I-cache, you configure the I-cache to
use zero, one, or both RAM sets

The I-cache can be enabled, disabled, or modified at any time by the program-
mer using software control. The TIPB bridge allows access to the cache con-
figuration registers in the DSP I/O space. At reset the I-cache is disabled. The
user must configure the I-cache to be able to use the ramset.

The initial normal cache hit is a one-wait-state operation. Thereafter, the
I-cache performs a simple branch prediction for cache access (i.e., a branch
not taken is always assumed). With this feature, no-branch continuous fetches
are no-wait-state operations. The instruction cache returns one 32-bit word for
each fetch. Fetches are always aligned on a 32-bit boundary.

When a cache miss occurs, wait states are inserted that are dependent upon
the external memory access time. The I-cache retrieves instructions from ex-
ternal memory in a burst of four 32-bit words (to fill cache line). To reduce the
penalty of misses, a streaming feature is implemented where the instruction
word requested by the DSP is sent back as soon as it is retrieved from external
memory, so all four 32 bit words do not have to be loaded into the cache line
first. Additionally, program fetch requests that fall in a cache line already being
retrieved due to a previous miss are serviced as soon as the word becomes
available. This streaming feature can increase the performance of even non-
looping code executing from external memory.

The instruction cache supports emulation debug read and breakpoint/watch-
point insertion by invalidating cache lines with the corresponding data
changed in the external memory space.

The DSP I-cache on OMAP5910 functions as described in the TMS320C55x
DSP Instruction Cache Reference Guide (literature number SPRU576). See
this document (I-Cache Type A section) for additional details on the DSP
I-cache operation.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Omnia 11 Installation And Operation Manual preview
11
Brand: Omnia Pages: 102
Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
XIA Pixie-4 Express Software Manual preview
Pixie-4 Express
Brand: XIA Pages: 17
Aleratec 310108 Quick Start Manual preview
310108
Brand: Aleratec Pages: 12
Falcon 4G COMBO User Manual preview
4G COMBO
Brand: Falcon Pages: 24
Dentsply Sirona inLab Speedcure 9494800 Instruction Manual preview
inLab Speedcure 9494800
Brand: Dentsply Sirona Pages: 91
Nvidia DGX A100 User Manual preview
DGX A100
Brand: Nvidia Pages: 115
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Brand: Magma Pages: 74
JETWAY I848ASR1A User Manual preview
I848ASR1A
Brand: JETWAY Pages: 47
Xyclop XC-16CH-NVR-4TB Quick Start Manual preview
XC-16CH-NVR-4TB
Brand: Xyclop Pages: 19
Patton electronics 593/45 User Manual preview
593/45
Brand: Patton electronics Pages: 8
LevelOne WBA-4000 User Manual preview
WBA-4000
Brand: LevelOne Pages: 49
IBM SA23-1325-01 Installation And Using Manual preview
SA23-1325-01
Brand: IBM Pages: 44
Ezquest Boa K16766 User Manual preview
Boa K16766
Brand: Ezquest Pages: 65
Hama 62732 Operating Instructions Manual preview
62732
Brand: Hama Pages: 34
Radionics D6600 NetCom System Manual preview
D6600 NetCom
Brand: Radionics Pages: 100

Brands by name

Popular brands

Load more brands