manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

TMS320C55x DSP CPU Overview

 

3-6

3.2

TMS320C55x DSP CPU Overview

Features for the high-performance, low-power C55x DSP CPU include:

-

Advanced multiple-bus architecture with one internal program memory
bus and five internal data buses (three dedicated to reads and two
dedicated to writes)

-

Unified program/data memory architecture

-

Dual 17-bit x17-bit multipliers coupled to 40-bit dedicated adders for non-
pipelined single-cycle multiply accumulate (MAC) operations

-

Add/compare/select (CSSU) unit for the add/compare section of the
Viterbi operator

-

Exponent encoder to compute an exponent value of a 40-bit accumulator
value in a single cycle

-

Two address generators with eight auxiliary registers and two auxiliary
register arithmetic units

-

8M x 16-bit (16M-bytes) total addressable memory space

-

Single-instruction repeat or block repeat operations for program code

-

Conditional execution

-

Seven-stage pipeline for high instruction throughput

-

Instruction buffer unit that loads, parses, queues, and decodes instruc-
tions to decouple the program fetch function from the pipeline

-

Program flow unit that coordinates program actions among multiple
parallel CPU functional units

-

Address data flow unit that provides data address generation and includes
a 16-bit arithmetic unit capable of performing arithmetic, logical, shift, and
saturation operations

-

Data computation unit containing the primary computation units of the
CPU, including a 40-bit arithmetic logic unit, two MAC units, and a shifter

3.2.1

On-Chip Memory

Features include:

-

DARAM that supports two memory accesses per cycle per block

-

SARAM that supports one memory access per cycle per block

-

PDROM that provides nonvolatile storage for program or data

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
H3C LSWM12H2Q User Manual preview
LSWM12H2Q
Brand: H3C Pages: 9
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Brand: FUNcube Pages: 23
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
ACTi LPR-100 Quick Installation Manual preview
LPR-100
Brand: ACTi Pages: 14
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
Ampro Corporation LITTLE BOARD P5X Hardware User Manual preview
LITTLE BOARD P5X
Brand: Ampro Corporation Pages: 121
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
Vista VIPER H4 User Manual preview
VIPER H4
Brand: Vista Pages: 93
R.V.R. Elettronica PTX30-UHT Installation, Technical And Maintenance Manual preview
PTX30-UHT
Brand: R.V.R. Elettronica Pages: 171
Multi-Tech RJModem MT5656RJ Developer'S Manual preview
RJModem MT5656RJ
Brand: Multi-Tech Pages: 27
Paradyne Application Module 9109 OCU-DP Installation Instructions Manual preview
Application Module 9109 OCU-DP
Brand: Paradyne Pages: 8
FiberHome AN5506-04 Series Product Manual preview
AN5506-04 Series
Brand: FiberHome Pages: 146
Lenze L-force MC-PNC Mounting Instructions preview
L-force MC-PNC
Brand: Lenze Pages: 46
AMX RDD-DM6/277 Schematic Diagram preview
RDD-DM6/277
Brand: AMX Pages: 1

Brands by name

Popular brands

Load more brands