Texas Instruments OMAP36 Series Technical Reference Manual Download

Page: 634 / 3738

Public Version

PRCM Register Manual

www.ti.com

Table 3-459. PRM_RSTST

Address Offset

0x0000 0058

Physical Address

0x4830 7258

Instance

Global_Reg_PRM

Description

This register logs the global reset sources. Each bit is set upon release of the domain reset signal. Must
be cleared by software.

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

RESERVED

ICEPICK_RST

MPU_WD_RST

GLOBAL_SW_RST

ICECRUSHER_RST

GLOBAL_COLD_RST

EXTERNAL_WARM_RST

VDD2_VOLTAGE_MANAGER_RST

VDD1_VOLTAGE_MANAGER_RST

Bits

Field Name

Description

Type

Reset

31:11

RESERVED

Write 0s for future compatibility. Read returns 0.

0x000000

ICECRUSHER_RST

IceCrusher reset event. This is a source of warm reset

0x0

initiated by the emulation.

Read 0x0: No IceCrusher reset.

Write 0x0: Status bit unchanged

Read 0x1: IceCrusher reset occurred.

Write 0x1: Status bit is cleared to 0.

ICEPICK_RST

IcePick reset event. This is a source of warm reset

0x0

initiated by the emulation.

Read 0x0: No IcePick reset.

Write 0x0: Status bit unchanged

Read 0x1: IcePick reset occurred.

Write 0x1: Status bit is cleared to 0.

VDD2_VOLTAGE_MANAGER_R VDD2 voltage manager reset event

0x0

Read 0x0: No VDD2 voltage manager reset.

Write 0x0: Status bit unchanged

Read 0x1: VDD2 voltage manager reset occurred.

Write 0x1: Status bit is cleared to 0.

VDD1_VOLTAGE_MANAGER_R VDD1 voltage manager reset event

0x0

Read 0x0: No VDD1 voltage manager reset.

Write 0x0: Status bit unchanged

Read 0x1: VDD1 voltage manager reset occurred.

Write 0x1: Status bit is cleared to 0.

EXTERNAL_WARM_RST

External warm reset event

0x0

Read 0x0: No global warm reset.

Write 0x0: Status bit unchanged

Read 0x1: Global external warm reset occurred.

Write 0x1: Status bit is cleared to 0.

RESERVED

Reserved for non-GP devices.

0x0

634

Power, Reset, and Clock Management

SWPU177N – December 2009 – Revised November 2010

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands

Texas Instruments OMAP36 Series, Technical Reference Manual

Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands