manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 3342

Public Version

High-Speed USB Host Subsystem

www.ti.com

Bits

Field Name

Description

Type

Reset

18

PSSC

Port 2 suspend status changed. This bit is set when the

RW

0

Port 2 port suspend status has changed.
Write 0x0: No effect.
Write 0x1: Clears this bit.

17

PESC

Port 2 enable status change. This bit is set when the Port

RW

0

2 port enable status has changed.
Write 0x0: No effect.
Write 0x1: Clears this bit.

16

CSC

Port 2 connect status change. This bit is set when the

RW

0

Port 2 port current connect status has changed due to a
connect or disconnect event.
If current connect status is 0 when a set port reset, set
port enable, or set port suspend write occurs, this bit is
set.
Write 0x0: No effect.
Write 0x1: Clears this bit.
Note: If the DR bit

HCRHDESCRIPTORB

[1] is set, this bit

is set only after a root hub reset to inform the system that
the device is attached.

15:10

RESERVED

Reserved

R

0x00

9

LSDA_CPP

Port 2 low-speed device attached/clear port power. This

RW

0

bit is valid only when port 2 current connect status is 1.
Read 0x0: A full-speed device is attached to port 2.
Read 0x1: A low-speed device is attached to port 2.
Write 0x0: No effect.
Write 0x1: Clears the port 2 port power status.

8

PPS_SPP

Port 2 port power status/set port power.

RW

0

Read 0x0: Port 2 power is enabled.
Read 0x1: Port 2 power is not enabled.
Write 0x0: No effect.
Write 0x1: Sets the port 2 port power status bit.

7:5

RESERVED

Reserved

R

0x0

4

PRS_SPR

Port 2 port reset status/set port reset.

RW

0

Read 0x0: USB reset is not being sent to port 2.
Read 0x1: Port 2 is signaling the USB reset.
Write 0x0: No effect.
Write 0x1: Sets the port 2 port reset status bit and causes
the USB host controller to begin signaling USB reset to
port 2.

3

RESERVED

Reserved

RW

0

2

PSS_SPS

Port 2 port suspend status/set port suspend. This bit is

RW

0

cleared automatically at the end of the USB resume
sequence and also at the end of the USB reset
sequence.
Write 0x0: No effect.
Read 0x0: Port 2 is not in the USB suspend state.
Read 0x1: Port 2 is in the USB suspend state or is in the
resume sequence.
Write 0x1: If port 2 current connect status is 1, sets the
port 2 port suspend status bit and places port 2 in USB
suspend state. If current connect status is 0, sets instead
connect status change to inform the USB host controller
driver of an attempt to suspend a disconnected port.

1

PES_SPE

Port 2 port enable status/set port enable. This bit is

RW

0

automatically set at completion of port 2 USB reset if it
was not already set before the USB reset completed, and
is automatically set at the end of a USB suspend if the
port was not enabled when the USB resume completed.
Read 0x0: Port 2 is not enabled.
Read 0x1: Port 2 is enabled.
Write 0x0: No effect.
Write 0x1: When port 2 current connect status is 1 sets
the port 2 port enable status bit. When port 2 current
status is 0 has no effect.

3342

High-Speed USB Host Subsystem and High-Speed USB OTG Controller

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands