manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 3233 / 3738

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 3233

Public Version

www.ti.com

High-Speed USB Host Subsystem

Table 22-22. OTG_BIGENDIAN

Address Offset

0x0000 0418

Physical Address

Instance

USBHS

See

Table 22-9

Description

Enable BIG ENDIANESS for OCP MASTER

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

BIG_ENDIAN

Bits

Field Name

Description

Type

Reset

31:1

RESERVED

Reserved

R

0x0000 0000

0

BIG_ENDIAN

Enable BIG ENDIAN in OCP MASTER

RW

0x0

0x0 Little Endian

0x1 Big Endian

Table 22-23. Register Call Summary for Register OTG_BIGENDIAN

High-Speed USB OTG Controller

•

High-Speed USB OTG Controller Registers

:

[0]

22.2 High-Speed USB Host Subsystem

NOTE:

Copyright ©2004,2005, 2006, 2007, 2008 Synopsys, Inc. All rights reserved. Used with

permission.

22.2.1 High-Speed USB Host Subsystem Overview

The high-speed universal serial bus (USB) host subsystem is composed of the high-speed multiport USB
host controller and the USBTLL module.

The USB controller is a high-speed multiport USB2.0 host controller. It contains two independent, 3-port
host controllers that operate in parallel:

•

The EHCI controller, based on the Enhanced Host Controller Interface (EHCI) specification for USB
Release 1.0, is in charge of high-speed traffic (480M bit/s), over the ULPI/UTMI interface

•

The OHCI controller, based on the Open Host Controller Interface (OHCI) specification for USB
Release 1.0a, is in charge of full-speed/low-speed traffic (12/1.5M bit/s, respectively), over a serial
interface

Each of the three device external ports is owned by exactly one and only one of the controllers at any
time.

The USBTLL module is a high-speed USB UTMI low-pin interface (ULPI) transceiverless link logic (TLL)
adapter. It implements a TLL compatible with a number of USB standard interface protocols. It consists of
three channels, defined as independent USB path through the TLL module, which always converts the
UTMI+ PHY interface protocol coming from the high-speed USB host controller.

Each USB port (1, 2, and 3) can connect either to an external-to-device chip USB transceiver or directly
using a transceiverless link to an external integrated circuit (IC) supporting the same TLL protocol.

Figure 22-8

highlights the high-speed USB host subsystem.

3233

SWPU177N – December 2009 – Revised November 2010

High-Speed USB Host Subsystem and High-Speed USB OTG Controller

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments