manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 1983 / 3738

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 1983

Public Version

www.ti.com

SGX Register Manual

Table 8-32. OCP_IRQENABLE_CLR_2

Address Offset

0x0000 FE50

Physical Address

Instance

SGX

Please refer to

Table 8-3

Description

Disable Interrupt 2 -Thalia (core) interrupt

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

THALIA_IRQ_DISABLE

Bits

Field Name

Description

Type

Reset

31:1

RESERVED

R

0x0000 0000

0

THALIA_IRQ_DISABLE

Disable interrupt 2 - Thalia (core) interrupt

RW

0

Write 0x0: no action.

Read 0x0: interrupt is enabled.

Read 0x1: interrupt is disabled.

Write 0x1: disable interrupt.

Table 8-33. Register Call Summary for Register OCP_IRQENABLE_CLR_2

SGX Register Manual

•

SGX OCP Register Summary

:

[0]

Table 8-34. OCP_PAGE_CONFIG

Address Offset

0x0000 FF00

Physical Address

Instance

SGX

Please refer to

Table 8-3

Description

Configure memory pages..

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

OCP_PAGE_SIZE

MEM_PAGE_SIZE

MEM_PAGE_CHECK_EN

1983

SWPU177N – December 2009 – Revised November 2010

2D/3D Graphics Accelerator

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments