background image

IDE/Compiler

Version Number

Notes

IAR Embedded Workbench

Not affected

C code is not impacted by this bug. 
User using POPM instruction in 
assembler is required to implement 
the above workaround manually.

TI MSP430 Compiler Tools (Code 
Composer Studio)

Not affected

C code is not impacted by this bug. 
User using POPM instruction in 
assembler is required to implement 
the above workaround manually.

MSP430 GNU Compiler (MSP430-
GCC)

Not affected

C code is not impacted by this bug. 
User using POPM instruction in 
assembler is required to implement 
the above workaround manually.

CPU47

CPU Module

Category

Functional

Function

An unexpected Vacant Memory Access Flag (VMAIFG) can be triggered

Description

An unexpected Vacant Memory Access Flag (VMAIFG) can be triggered, if a PC-
modifying instruction (e.g. - ret, push, call, pop, jmp, br) is fetched from the last addresses 
(last 4 or 8 byte) of a memory (e.g.- FLASH, RAM, FRAM) that is not contiguous to a 
higher, valid section on the memory map.
In debug mode using breakpoints the last 8 bytes are affected.
In free running mode the last 4 bytes are affected.

Workaround

Edit the linker command file to make the last 4 or 8 bytes of affected memory sections 
unavailable, to avoid PC-modifying instructions on these locations.
Remaining instructions or data can still be stored on these locations.

DMA4

DMA Module

Category

Functional

Function

Corrupted write access to 20-bit DMA registers

Description

When a 20-bit wide write to a DMA address register (DMAxSA or DMAxDA) is interrupted 
by a DMA transfer, the register contents may be unpredictable.

Workaround

1. Design the application to guarantee that no DMA access interrupts 20-bit wide 
accesses to the DMA address registers.

OR

2. When accessing the DMA address registers, enable the Read Modify Write disable bit 
(DMARMWDIS = 1) or temporarily disable all active DMA channels (DMAEN = 0).

OR

3. Use word access for accessing the DMA address registers. Note that this limits the 
values that can be written to the address registers to 16-bit values (lower 64K of Flash).

DMA7

DMA Module

www.ti.com

Advisory Descriptions

SLAZ481AD – DECEMBER 2012 – REVISED MAY 2021

Submit Document Feedback

MSP430F6767 Microcontroller

13

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for MSP430F6767




























Reviews: