background image

www.ti.com

Overview

5

SBOU230 – October 2019

Submit Documentation Feedback

Copyright © 2019, Texas Instruments Incorporated

INA290EVM

2

Overview

The INA290-Q1 device is a voltage-output, high-side current sense amplifier with an enable pin in a very-
small SC-70 (5) package. As shown in

Table 1

the INA290 has gains that range from 20 V/V to 500 V/V,

depending on the gain option that is selected. The voltage developed across the device inputs is amplified
by the corresponding gain of the specific device, and is presented at the output pin. The device can
accurately sense voltage drops across shunts at 2.7-V to +110-V common-mode voltages, dependent of
supply voltages.The device survives common-mode voltages from –20 V to +120 V. The device operates
with supply voltages between 2.7 V and 20 V, and draws a typical of 350 µA at room temperature.

(1)

INA290B-Q1 is a preview device.

Table 1. INA290 Gain Option Summary

Product

(1)

Gain (V/V)

INA290A1

20

INA290A2

50

INA290A3

100

INA290A4

200

INA290A5

500

2.1

EVM Kit Contents

Table 2

summarizes the contents of the INA290EVM kit. Contact the nearest

Texas Instruments Product

Information Center

if any component is missing. TI also recommends to check the

INA290-Q1 device

product folder

at

www.ti.com

for any further information regarding this product.

Table 2. INA290EVM Kit Contents

Item

Item Part Number

Quantity

INA290EVM test board

INA290EVM

1

2.2

Related Documentation From Texas Instruments

This document provides information regarding Texas Instruments' integrated circuits used in the assembly
of the INA290EVM.

Table 3. Related Documentation

Document

Literature Number

INA290-Q1

product data sheet

SBOS955

Summary of Contents for INA290EVM























Reviews: