manualshive.com logo in svg

Texas Instruments INA223EVM, User'S Manual And Software Tutorial, Page: 18 / 26

Share
Download
Texas Instruments INA223EVM User'S Manual And Software Tutorial Download Page 18

INA223EVM Software Overview

www.ti.com

5.2.3

Bus Voltage Gain

The Bus Voltage Gain field allows the user to select the gain that the bus voltage is multiplied by. It is
important to choose a value that places the output voltage within the linear output range of the device.
Failure to ensure that the outputs are within the linear range of the device can result in inaccurate results.

Figure 18. Configuring the Bus Voltage Gain

5.2.4

Current Shunt Voltage Gain

The Current Shunt Voltage Gain field is used to select the device shunt voltage gain setting. It is important
to choose a value that places the output voltage within the linear output range of the device. Failure to
ensure that the outputs are within the linear range of the device can result in inaccurate results.

Figure 19. Configuring the Current Shunt Voltage Gain

18

INA223EVM User’s Guide and Software Tutorial

SBOU125 – June 2012

Submit Documentation Feedback

Copyright © 2012, Texas Instruments Incorporated

Summary of Contents for INA223EVM



























Reviews:

No comments