Texas Instruments EMIF16 User Manual Download Page 15

Page: 15 / 63

2.5 ASRAM/NOR Flash Interface

SPRUGZ3A—May 2011

KeyStone Architecture External Memory Interface (EMIF16) User Guide

2-5

Submit Documentation Feedback

Chapter 2—Architecture

www.ti.com

Figure 2-3

Connecting to 8-bit ASRAM

Note—

EMIFA[23:22] behave as address selects. For 16-bit interface, EMIFA23

is connected to address pin A0 of the ASRAM/NOR Flash. For 8-bit interface,
EMIFA[23:22] are connected to address pins A[1:0] of the ASRAM/NOR
Flash.

2.5.1 EMIF16 Signal Description – ASRAM/NOR Flash

EMIFCE, EMIFWE, EMIFOE, EMIFBE[1:0] are the control signals that determine the
start and end of the read/write cycles.

Figure 2-4

and

Figure 2-5

show reads and writes

initiated by different control signals.

EMIFD [7:0]

EMIFA [21:0, 23, 22]

CE0

EMIFBE1

External

Memory

EMIFWE

Interface

(EMIF16)

EMIFOE

WAIT [1:0]

I/O [7:0]

A [N:0]

SRAM/NOR Flash

CS#

N+1

x 8

LB#

WE#

OE#

Vcc

EMIFBE0

Table 2-2

ASRAM/NOR Flash Interface Signals

EMIF16 Pin

ASRAM Pin

Description

EMIFD [15:0]

/EMIFD[7:0]

I/O [15:0]/

I/O[7:0]

Data I/O pins. 16/8-bit bidirectional data path for I/O.

EMIFA [23:0]

A[N:0]

External address outputs.

EMIFCE[3:0]

CS#

Chip select for CE space. Active-low chip select for memory spaces 0
to 3.

EMIFBE[1:0]

UB#/LB#

Active-low byte enables (Upper and lower). Individual bytes or
half-words can be selected.

EMIFOE

OE#

Active-low output enable. Low during read access period.

EMIFWE

WE#

Active-low write enable. Low during write transfer strobe period.

EMIFRnW

—

Read-write enable.

End of Table 2-2

Summary of Contents for EMIF16
































































Search results

Summary of Contents for EMIF16

Reviews:

Brands by name

Popular brands

Texas Instruments EMIF16, User Manual

Search results

Summary of Contents for EMIF16

Reviews:

Brands by name

Popular brands